Scheppach HG35 Original Bedienungsanleitung Seite 27

e) Maintain power tools and accessories. Check for
misalignment or binding of moving parts, break-
age of parts and any other condition that may af-
fect the power tool's operation. If damaged, have
the power tool repaired before use. Many acci-
dents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the power
tool for operations different from those intended
could result in a hazardous situation.
h) Keep handles and grasping surfaces dry,
clean and free from oil and grease.
Slippery handles and grasping surfaces do not
allow for safe handling and control of the tool in
unexpected situations.
5) Service
a) Have your power tool serviced by a qualified
repair person using only identical replace-
ment parts. This will ensure that the safety of
the power tool is maintained.
Warning! This power tool generates an electromag-
netic field during operation. This field can impair active
or passive medical implants under certain conditions.
In order to prevent the risk of serious or deadly injuries,
we recommend that persons with medical implants
consult with their physician and the manufacturer of
the medical implant prior to operating the power tool.
Safety instructions for all applications
Common safety instructions for grinding, sandpa-
per grinding, working with wire brushes, polish-
ing, milling or cut-off grinding:
a) This electric tool can be used as a grinder,
sandpaper grinder, wire brush, polisher, for
milling and as a cut-off grinder. Read all safety
warnings, instructions, illustrations and spec-
ifications provided with this power tool. Failure
to observe the following instructions may result in
electric shock, fire and / or serious injury.
b) Do not use accessories that are not specifical-
ly envisaged and recommended by the manu-
facturer for this electric tool. Just because the
accessory can be attached to your power tool, it
does not assure safe operation.
c) The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool. Accessories that rotate faster
than permitted can break and fly off at high speed.
d) The outside diameter and the thickness of your
accessory must be within the capacity rating
of your power tool. Incorrectly sized accessories
cannot be adequately guarded or controlled.
e) Grinding discs, grinding rollers or other ac-
cessories must fit exactly on the grinding
spindle or collet of your electric tool. Tool at-
tachments that do not fit exactly on your electri-
cal tool's receptacle rotate unevenly, vibrate very
strongly and can cause a loss of control.
f) Wheels/discs, grinding cylinders, cutting tools
or other accessories mounted on a work arbor
must be fully inserted into the collet or clamp-
ing chuck. The "protrusion" or the exposed
part of the work arbor between the grinding
body and the collet or clamping chuck must be
minimal. X If the work arbor is not sufficiently ten-
sioned or the grinding body is too far forward, the
tool attachment can come loose and be ejected at
high speed.
g) Do not use a damaged accessory. Before each
use, check insert tools such as grinding discs
for chipping and cracks, grinding rollers for
cracks, wear or heavy wear, wire brushes for
loose or broken wires. If power tool or acces-
sory is dropped, inspect for damage or install
an undamaged accessory. After inspecting
and installing an accessory, position yourself
and bystanders away from the plane of the
rotating accessory and run the power tool at
maximum no-load speed for one minute. Dam-
aged tool attachments usually break during this
test period.
Wear personal protective equipment. Depend-
h)
ing on application, use face shield, safety
goggles or safety glasses. Where appropriate,
wear a dust mask, hearing protection, protec-
tive gloves or a special apron that will keep
small grinding and material particles away
from you. The eye protection must be capable
of stopping flying debris generated by various op-
erations. Dust or breathing masks must filter the
dust generated during use. Prolonged exposure
to high intensity noise may cause hearing loss.
www.scheppach.com GB | 27