Seite 1
EN DE Notice d'utilisation voile | LEAF3 Light EN DE Notice d’utilisation LEAF3 light SUPAIR 34 rue Adrastée Parc Altaïs 74650 Annecy - Chavanod FRANCE www.supair.com 45°54.024’N / 06°04.725’E SUPAIR | LEAF3 Light | page 1...
Seite 2
SUPAIR conçoit, produit et commercialise des articles pour le vol libre depuis 1984. Choisir un produit SUPAIR, c'est ainsi s'assurer de 30 ans d'expertise, d'innovation et d'écoute. C'est aussi une philosophie: celle de se perfectionner toujours et de faire le choix d'une production de qualité.
Décollage Caractéristiques de vol Fin du vol Pratiques spécifiques Descentes rapides Incidents de vol Plan de suspente Matériaux Tableau de mesures Entretien Contrôles obligatoires Equipement du pilote Garantie Avis de non-responsabilité Recyclage Eco-Responsabilité SUPAIR | LEAF3 Light | page 3...
Elle peut être utilisée avec la plupart des sellettes disponibles sur le marché, mais pour un meilleur confort de vol et des sensations optimales nous vous conseillons les modèles de sellettes de progression de la gamme SUPAIR. Grâce à grande sécurité passive, la LEAF3 Light peut aussi être proposée en fin de formation aux élèves talentueux, sous la responsabi- lité...
* Hauteur des points * Hauteur des points * Hauteur des points * Hauteur des points d'attache: 40 ±1 cm d'attache: 40 ±1 cm d'attache: 42 ±1 cm d'attache: 42 ±1 cm d'attache: 44 ±1 cm SUPAIR | LEAF3 Light | page 5...
LEAF3 Light S LEAF3 Light M LEAF3 Light ML Plage de Poids Total Volant de la voile Plage de Poids Total Volant idéal pour exploiter au maximum les performances de la voile OCEAN SUNSET SUPAIR | LEAF3 Light | page 6...
Extrados Élévateur A Élévateur A' (pour les oreilles) Élévateur B Élévateur C Drisse de frein Attache de frein Poignée de frein Point d'accroche principal élévateur Sac Compact Case Pochette avec kit de réparation SUPAIR | LEAF3 Light | page 7...
Une fois l'accélérateur connecté, ajustez la longueur selon votre automatique taille. Pour une utilisation correcte, il ne doit pas y avoir de ten- sens de vol sion au niveau des crochets en position relâchée. SUPAIR | LEAF3 Light | page 8...
Que la voile est bien connectée aux élévateurs et que les mousquetons et les maillons sont bien verrouillés. Que la voile est bien connectée, sans tours de sellette. Que vous êtes bien attachés, (cuissardes, ventrale, mousquetons, casque...) SUPAIR | LEAF3 Light | page 10...
N.B. : il n'est pas nécessaire de prendre les élévateurs A' destinés aux oreilles. Attention ! Ne décollez jamais sans vous être assuré que l'espace aérien est libre et que les conditions correspondent à votre niveau de pra- tique. SUPAIR | LEAF3 Light | page 11...
Pour l'atterrissage laisser voler l'aile jusqu'au dernier moment où il faudra la freiner symétriquement. Freiner avec les C est moins efficace qu'avec les freins, l'atterrissage sera un peu plus tonique que la normale. SUPAIR | LEAF3 Light | page 12...
La voile LEAF3 Light n'a pas été conçue pour le vol acrobatique. Nous déconseillons son utilisation pour ce type de vol. Biplace Le parapente LEAF3 Light n'est pas conçu pour le vol en biplace SUPAIR | LEAF3 Light | page 13...
Pour rouvrir les oreilles, relâchez l'accélérateur, puis les élévateurs symétriquement. Conformément à la norme les oreilles se rou- vriront seules, mais vous pouvez effectuer un freinage ample d'un côté puis de l'autre pour faciliter la réouverture. SUPAIR | LEAF3 Light | page 14...
La pratique répétée de manœuvres sollicitant au delà de 4xG (ou 2xG si les manœuvres sont dissymétriques) entraîne un vieillissement pré- maturé de votre aile et est à proscrire. Les manœuvres de type "SAT" sont les plus traumatisantes pour votre matériel. SUPAIR | LEAF3 Light | page 15...
à nouveau aux commandes. Vrille / décrochage asymétrique Une vrille ne surviendra qu'en cas d'erreur de pilotage. Dans ce cas, remontez complètement la commande du côté décroché et contrôlez l'abattée consécutive. SUPAIR | LEAF3 Light | page 16...
5416 5417 5465 5536 Wingtip Tolérence +/- 10mm Tableau de mesures (mm) de la longueur des élévateurs * à remplir une fois mesuré par Air Turquoise Elévateurs Trim Accéléré Gamme Tolérence +/- 5mm SUPAIR | LEAF3 Light | page 19...
Seite 20
*La valeur coupée peut changée selon le type de couture , de machine et le fil utilisés ** la valeur cousue correspond à la longueur finale de la suspente, de la boucle d'une extrêmité à l'autre SUPAIR | LEAF3 Light | page 20...
Seite 21
5949 5943 Stabilizers 5658 5649 5659 5654 5711 5706 5784 5778 Wingtip Tolérence +/- 10mm Tableau de mesures (mm) de la longueur des élévateurs Elévateurs Trim Accéléré 130 mm Gamme Tolérence +/- 5mm SUPAIR | LEAF3 Light | page 21...
Seite 22
*La valeur coupée peut changée selon le type de couture , de machine et le fil utilisés Tolérence +/- 10mm ** la valeur cousue correspond à la longueur finale de la suspente, de la boucle d'une extrêmité à l'autre SUPAIR | LEAF3 Light | page 22...
Seite 23
6480 6486 Stabilizers Wingtip 6132 6129 6133 6129 6187 6183 6267 6263 Tolérence +/- 10mm Tableau de mesures (mm) de la longueur des élévateurs Elévateurs Trim Accéléré 142 mm Gamme Tolérence +/- 5mm SUPAIR | LEAF3 Light | page 23...
Seite 24
*La valeur coupée peut changée selon le type de couture , de machine et le fil utilisés ** la valeur cousue correspond à la longueur finale de la suspente, de la boucle d'une extrêmité à l'autre SUPAIR | LEAF3 Light | page 24...
Seite 25
6640 6864 6861 6472 6473 6473 6477 6530 6532 6614 6616 Wingtip Tolérence +/- 10mm Tableau de mesures (mm) de la longueur des élévateurs Elévateurs Trim Accéléré Gamme 142 mm Tolérence +/- 5mm SUPAIR | LEAF3 Light | page 25...
Seite 26
*La valeur coupée peut changée selon le type de couture , de machine et le fil utilisés ** la valeur cousue correspond à la longueur finale de la suspente, de la boucle d'une extrêmité à l'autre SUPAIR | LEAF3 Light | page 26...
Seite 27
6928 7144 7142 Wingtip 6751 6753 6752 6756 6812 6814 6899 6900 Tolérence +/- 10mm Tableau de mesures (mm) de la longueur des élévateurs Elévateurs Trim Accéléré 150 mm Gamme Tolérence +/- 5mm SUPAIR | LEAF3 Light | page 27...
Seite 28
*La valeur coupée peut changée selon le type de couture , de machine et le fil utilisés ** la valeur cousue correspond à la longueur finale de la suspente, de la boucle d'une extrêmité à l'autre SUPAIR | LEAF3 Light | page 28...
Seite 29
LEAF3 Light XXS Numéro de certification: (Données bientôt disponibles) LEAF3 Light XS Numéro de certification: N° PG_2109.2023 Supair LEAF 3 light XS LEAF3 Light S Numéro de certification: N° PG_2104.2023 Supair LEAF 3 light S LEAF3 Light M Numéro de certification: N°...
à l'exposition à des substances chimiques, un contrôle de votre voile en atelier agréé doit impérati- vement être effectué. Il en va de votre sécurité. • SUPAIR préconise de remplacer les mousquetons tous les 5 ans ou dès qu'ils ont du mal à se fermer ou encore s'ils portent des marques d'usure. SUPAIR...
Malgré l'emploi de matériaux de qualité, il se peut que votre aile subisse des détériorations. Dans ce cas, il faut la faire contrôler et la faire réparer dans un atelier spécialisé. SUPAIR offre la possibilité de réparer les produits qui connaîtraient une perte totale ou partielle d'une de ses fonctions au-delà de la période normale de garantie.
Garantie SUPAIR apporte le plus grand soin à la conception et la production de ses produits. SUPAIR garantit ses voiles de parapente 3 ans (à partir de la date d'achat) contre toute malfaçon ou défaut de conception qui se présenterait dans le cadre d'une utilisation normale du produit. Toute utilisation abusive ou incorrecte, toute exposition hors de proportion à...
Seite 33
SUPAIR Parc Altaïs 34 rue Adrastée 74650 Chavanod, Annecy FRANCE info@supair.com +33(0)4 50 45 75 29 45°54.024’N / 06°04.725’E...
Seite 35
SUPAIR has been designing producing and sel- ling accessories for free flying activities since 1984. By choosing a SUPAIR product you benefit from almost thirty years of expertise, innovation and customer care. We pride ourselves for our work ethics and customer care.
Seite 36
Equipment overview Connecting the glider Pre-flight preparation Take-off Flight characteristics End of the flight Specific practices Fast descents Flight incidents Line layout Materials Measurement table Maintenance Mandatory checks Pilot equipment Warranty Disclaimer Recycling Eco-responsibility SUPAIR | LEAF3 Light | page 3...
It can be used with most harnesses found on the market today. For better inflight comfort and sensations we will advise you to choose the SUPAIR progression harness models. Thanks to its great passive safety, the LEAF3 Light may be flown by talented pilots undertaking a paragliding beginner course, under the supervision of their instructor and provided that their abilities have been positively evaluated by the instructor and that it is legally possible in the country where this course is being taken.
* Height of main suspen- * Height of main suspen- sion points: 40 ±1 cm sion points: 40 ±1 cm sion points: 42 ±1 cm sion points: 42 ±1 cm sion points: 44 ±1 cm SUPAIR | LEAF3 Light | page 5...
Leading edge Trailing edge Stabilizer Intrados Extrados A riser « A » split risers (for Big Ears) B riser C riser Brake line Brake holder Brake handle Riser hook-up loop Compact Case Pocket with repair kit SUPAIR | LEAF3 Light | page 7...
Once the accelerator/speedbar is connected, adjust its length according to your measurements. For correct use, there must not be any tension at the Flight direction split-hook level when the accelerator/speedbar line is relaxed. SUPAIR | LEAF3 Light | page 8...
Be certain to adjust and leave a small amount of line slack to keep steering toggle play, prevent wing profile deformation and hinder the accelerator func- tionality. During acceleration, the glider's trailing edge must not be deformed. SUPAIR | LEAF3 Light | page 9...
- The wing is properly connected to the harness without any riser twist. - You are securely connected to the harness with the leg and chest strap buckles closed, self-locking carabiners locked. - Your are wearing your helmet and it is properly fastened. SUPAIR | LEAF3 Light | page 10...
Note: it is not necessary to use the "A" risers to inflate the wing. Caution ! Before take-off, ensure for the airspace to be clear in front, around and above you with weather conditions matching your flying skill level.. SUPAIR | LEAF3 Light | page 11...
To land, let your wing glide for as long as possible before applying a full braking motion. Braking using the "C" risers is not as effi- cient as using the toggles and could bring a more energetic landing than normal. SUPAIR | LEAF3 Light | page 12...
Aerobatics The LEAF3 Light wing was not designed to enter We highly discourage its use for this type of flying. Tandem The LEAF3 Light wing was not designed for tandem flying. SUPAIR | LEAF3 Light | page 13...
Seite 47
To reopen the "Ears", bring the accelerator/speedbar back to its neutral default setting, then let go the risers symmetrically. You can pump the brake/toggles on either side of the wing to facilitate its reopening sequence. SUPAIR | LEAF3 Light | page 14...
Repeated practice of said exercise exceeding 4xG (or 2xG if they are asymmetrical) will cause premature aging of your glider and is to be avoided. “SAT” maneuvers are the most damaging to your equipment. SUPAIR | LEAF3 Light | page 15...
A spin will only occur because of a piloting error. If so, release the brake fully on the stalled side and be certain to keep the glider in check during the ensuing dive and reopening sequence. SUPAIR | LEAF3 Light | page 16...
Top cascade Edelrid 8000U serie / 050 Upper middle cascade Edelrid 8000U serie / 090 Lower middle cascade Edelrid 8000U serie / 90 - 130 Lower cascade Edelrid A7850X-240-041 Carabiners Supair Soft link dyneema SUPAIR | LEAF3 Light | page 18...
Seite 52
5824 5715 Stabilizers 5600 5554 5693 5416 5417 5465 5536 Wingtip Tolerance +/- 10mm Riser length measurement (mm) table *to fill once measured by Air turquoise Risers Trim Accelerated Range Tolerance +/- 5mm SUPAIR | LEAF3 Light | page 19...
Seite 53
Lines lenghts under 5 kg of tension: *the cut value may differ according to the type of stitching/machine and the thread used **the sewn value is the final length of the line, from one loop end to the other SUPAIR | LEAF3 Light | page 20...
Seite 54
5968 5851 5847 5802 5800 5949 5943 Stabilizers Wingtip 5658 5649 5659 5654 5711 5706 5784 5778 Tolerance +/- 10mm Line Check Maintenance Sheet Risers Trim Accelerated Range 130 mm Tolerance +/- 5mm SUPAIR | LEAF3 Light | page 21...
Seite 55
*the cut value may differ according to the type of stitching/machine and the thread used Tolérence +/- 10mm **the sewn value is the final length of the line, from one loop end to the other SUPAIR | LEAF3 Light | page 22...
Seite 57
Lines lenghts under 5 kg of tension: *the cut value may differ according to the type of stitching/machine and the thread used **the sewn value is the final length of the line, from one loop end to the other SUPAIR | LEAF3 Light | page 24...
Seite 59
Lines lenghts under 5 kg of tension: *the cut value may differ according to the type of stitching/machine and the thread used **the sewn value is the final length of the line, from one loop end to the other SUPAIR | LEAF3 Light | page 26...
Seite 61
Lines lenghts under 5 kg of tension: *the cut value may differ according to the type of stitching/machine and the thread used **the sewn value is the final length of the line, from one loop end to the other SUPAIR | LEAF3 Light | page 28...
Seite 62
Certificates LEAF3 Light XXS Certification number: Data coming soon LEAF3 Light XS Certification number: N° PG_2109.2023 Supair LEAF 3 light XS LEAF3 Light S Certification number: N° PG_2104.2023 Supair LEAF 3 light S LEAF3 Light M Certification number: N° PG_2105.2023 Supair LEAF 3 light M...
Taking a good care of your light wing SUPAIR takes the greatest care in the design of your wing, but we would like to remind you that a "light" wing is usually more fragile than a classic wing. To ensure a lot of flight and your glider's optimal durability, we will recommend some specials daly cares as follow : •...
It is essential to wear a helmet, suitable shoes with good ankle support and adapted clothing. Carrying a reserve emergency parachute corresponding to your weight and properly connected to the harness is also highly recommended. The entire SUPAIR harness, accessory and reserve parachute selection (except for tandem gear), is compatible with the LEAF3 Light glider.
Warranty SUPAIR takes the greatest care in the design and production of its product line hence offers a 3 years limited warranty from the purchase date against any manu- facturing defect or design issues occ urring during normal use. Any damage or degradation resulting from incorrect or abusive use, abnormal exposure to ag- gressive factors including but not limited to;...
Seite 66
SUPAIR Parc Altaïs 34 rue Adrastée 74650 Chavanod, Annecy FRANCE info@supair.com +33(0)4 50 45 75 29 45°54.024’N / 06°04.725’E...
Seite 67
Gleitschirm Betriebsanleitung | LEAF3 Light Betriebshandbuch LEAF3 light SUPAIR 34 rue Adrastée Parc Altaïs 74650 Annecy - Chavanod FRANCE www.supair.com 45°54.024’N / 06°04.725’E SUPAIR | LEAF3 Light | Seite 1...
Seite 68
SUPAIR entwickelt, produziert und vertreibt Produkte für den Flugsport seit 1984. Durch die Wahl eines SUPAIR Produktes profitierst du von mehr als 30 Jahren Fachwissen, Innovationen und Image. Unsere Philosophie ist die permanenten Bedürfnisse der Piloten anzuhören, um bessere Produkte zu entwickeln...
Seite 69
Überblick der Ausrüstung Verbindung des Gleitschirms Flugvorbereitungen Start Flugverhalten Ende des Flugs Spezifischer Gebrauch Schnellabstieg Besondere Fälle im Flug Leinenplan Materialien Tabelle der Messwerte Wartung Vorgeschriebene Kontrollen Piloten Ausrüstung Garantie Haftungsausschluss Recycling Umweltverantwortung SUPAIR | LEAF3 Light | Seite 3...
Nach dem Lesen der Betriebsanleitung weisen wir dich darauf hin, zuerst den Flügel an einem Übungshang aufzuziehen, ihn zu kontrol- lieren und zu testen. Übrigens: Drei Faktoren werden dir helfen das Betriebshandbuch zu lesen. Hinweis Achtung! Gefahr!! SUPAIR | LEAF3 Light | Seite 4...
Gleitschirm Betriebsanleitung | LEAF3 Light Überblick der Ausrüstung Eintrittskante Hinterkante Stabilo Untersegel Obersegel A Tragegurt A' Tragegurt (zum Ohrenanlegen) B Tragegurt C Tragegurt Bremsleine Bremsführung Bremsgriff Tragegurteinhängungsschlaufe Packsack Compact case Tasche mit Reparaturmaterial SUPAIR | LEAF3 Light | Seite 7...
Wenn das Beschleunigungssystem eingehängt ist, stelle die Länge entsprechend deiner Abmessungen ein. Für den richtigen Gebrauch Flugrichtung darf keine Spannung auf den Brummelhaken bzw. auf der Beschleuni- gerleine sein, wenn der Beschleuniger nicht benützt wird. SUPAIR | LEAF3 Light | Seite 8...
Durchhang an der Steuerleine, damit die Steuer- schlaufe Spiel hat, um einer Deformation des Profils und einer Einschränkung der Funktionalität des Be- schleunigers vorzubeugen. Während der Beschleu- nigung darf die Hinterkante des Gleitschirms nicht deformiert werden. Beschleunigter Flugzustand SUPAIR | LEAF3 Light | Seite 9...
• dass der Schirm korrekt mit dem Gurtzeug verbunden ist und dies ohne irgendwelcher Verdrehungen von Gurten und Leinen. • dass du sicher mit deinem Gurtzeug mit geschlossenen Beingurten, Brustgurten und Karabinern verbunden bist. Deinen Helm musst du tragen, schließen und korrekt festziehen..SUPAIR | LEAF3 Light | Seite 10...
Bemerkung: es ist nicht notwendig die "A" Tragegurte zu benützen, um den Schirm zu füllen. Achtung! Vor dem Start vergewissere dich immer, dass der Luftraum frei ist und die Verhältnisse geeignet sind für dein Wissen und Können. SUPAIR | LEAF3 Light | Seite 11...
Bei der Landung lasse deinen Flügel so lang wie möglich gleiten bevor du eine komplette symmetrische Bremsbewegung machst. Bremsen mit den "C" Tragegurten ist nicht so effizient, wie wenn man die Bremsgriffe verwendet und kann eine härtere Landung verursachen als normal. SUPAIR | LEAF3 Light | Seite 12...
Kunstflug Der LEAF3 Light Gleitschirm wurde nicht für Kunstflug/Acro Manövern gebaut. Wir raten dringlich von der Ausübung dieser Art vom Fliegen ab. Tandem Der LEAF3 Light Gleitschirm ist nicht für das Tandemfliegen geeignet. SUPAIR | LEAF3 Light | Seite 13...
Um die „Ohren“ wieder zu öffnen, bringe den Beschleuniger zurück zur neutralen Ausgangsposition, dann lasse die Tragegurte symmetrisch los. Gemäß der Norm sollten die Ohren alleine öffnen. Du darfst die Bremse an einer Seite mit dosierten Pumpen einsetzte SUPAIR | LEAF3 Light | Seite 14...
Dein Schirm wurde nicht für Freestyle- oder Acromanöver entwickelt! Wiederholtes üben von Manövern mit Belastungen über 4G (oder über 2G bei asymmetrischen), reduzieren die Haltbarkeit deines Schirmes rapide und sind zu vermeiden. „SAT“-Manöver schädigen deinem Equipment am meisten. SUPAIR | LEAF3 Light | Seite 15...
Ein Einseitiger Strömungsabriss wird nur vorkommen bei Pilotenfehlern. Falls dies eintritt, löse komplett an der angestallten Seite die Bremse und stelle sicher, dass du den Gleitschirm kontrolliert behältst bis in das darauf folgende Durchtauchen. SUPAIR | LEAF3 Light | Seite 16...
5824 5715 5600 5554 5693 Stabilizers Wingtip 5416 5417 5465 5536 Toleranz +/- 10mm Tabelle Der Messwerte (mm) Tragegurtlänge *to fill once measured by Air turquoise Ebene Trim Beschleunigt Range Toleranz +/- 5mm SUPAIR | LEAF3 Light | Seite 19...
* Cut value, das heisst Wert vor dem Schneiden, kann nach der und dem Faden anders werden ** Sewn value, das heisst Wert nach dem Nähen, ist die Endlänge zwischen die beide Loops SUPAIR | LEAF3 Light | Seite 20...
5949 5943 Stabilizers 5658 5649 5659 5654 5711 5706 5784 5778 Wingtip Toleranz +/- 10mm Tableau de mesures (mm) de la longueur des élévateurs Ebene Trim Beschleunigt 130 mm Gamme Toleranz +/- 5mm SUPAIR | LEAF3 Light | Seite 21...
Seite 88
* Cut value, das heisst Wert vor dem Schneiden, kann nach der und dem Faden anders werden Toleranz +/- 10mm ** Sewn value, das heisst Wert nach dem Nähen, ist die Endlänge zwischen die beide Loops SUPAIR | LEAF3 Light | Seite 22...
Stabilizers 6339 6334 6287 6284 6480 6486 6132 6129 6133 6129 6187 6183 6267 6263 Wingtip Toleranz +/- 10mm Tabelle Der Messwerte (mm) Tragegurtlänge Ebene Trim Beschleunigt 142 mm Range Toleranz +/- 5mm SUPAIR | LEAF3 Light | Seite 23...
Seite 90
* Cut value, das heisst Wert vor dem Schneiden, kann nach der Nähmaschine und dem Faden anders werden ** Sewn value, das heisst Wert nach dem Nähen, ist die Endlänge zwischen die beide Loops SUPAIR | LEAF3 Light | Seite 24...
6691 6695 6636 6640 6864 6861 Stabilizers Wingtip 6472 6473 6473 6477 6530 6532 6614 6616 Toleranz +/- 10mm Tabelle Der Messwerte (mm) Tragegurtlänge Ebene Trim Beschleunigt 142 mm Range Toleranz +/- 5mm SUPAIR | LEAF3 Light | Seite 25...
Seite 92
* Cut value, das heisst Wert vor dem Schneiden, kann nach der Nähmaschine und dem Faden anders werden ** Sewn value, das heisst Wert nach dem Nähen, ist die Endlänge zwischen die beide Loops SUPAIR | LEAF3 Light | Seite 26...
6979 6983 6922 6928 7144 7142 Stabilizers Wingtip 6751 6753 6752 6756 6812 6814 6899 6900 Toleranz +/- 10mm Tabelle Der Messwerte (mm) Tragegurtlänge Ebene Trim Beschleunigt Range 150 mm Toleranz +/- 5mm SUPAIR | LEAF3 Light | Seite 27...
Seite 94
* Cut value, das heisst Wert vor dem Schneiden, kann nach der Nähmaschine und dem Faden anders werden ** Sewn value, das heisst Wert nach dem Nähen, ist die Endlänge zwischen die beide Loops SUPAIR | LEAF3 Light | Seite 28...
UV-Strahlung, Abrieb, Feuchtigkeit oder Aussetzung chemischer Substanzen, Dämpfen wie auch Benzin. An deinem Gleitschirm muss regelmäßig ein kompletter Check in einer qualifizierten Werkstatt durchgeführt werden. • Die Karabiner müssen im 5 Jahreszyklus mit identischen Model erneuert werden oder Modelle die vom Hersteller (SUPAIR) empfohlen. SUPAIR | LEAF3 Light | Seite 30...
Auch nach Ablauf der Garantiezeit bietet SUPAIR dir die Möglichkeit das Produkt zu reparieren. Dies wäre in der Praxis ein Teil- oder Totalscha- den. Wir Danken dir für deinen Anruf oder dein E-Mail sav@supair.com, um dir einen Kostenvoranschlag zu machen.
Garantie SUPAIR achtet besonders auf die Entwicklung und Produktion ihrer Produkte. SUPAIR gibt 3 Jahre (vom Verkaufsdatum) Garantie auf ihre Produkte, sei es wegen irgendwelchen Defekten oder Konstruktionsfehlern, die unter normalen Gebrauch auftreten. Bei irgendeinen unsachgemäßen Gebrauch, starker Abnutzung oder abnormale Aussetzung von schädlichen Faktoren wie Z.B.
Seite 99
SUPAIR Parc Altaïs 34 rue Adrastée 74650 Chavanod, Annecy FRANCE info@supair.com +33(0)4 50 45 75 29 45°54.024’N / 06°04.725’E...