Gaggenau CV492100 Montageanleitung Seite 22

Connect the circulating-air duct to the flat duct el-
2.
bow on the rear of the hob.
→ Fig.
52
Connect the diffuser to the circulating-air duct.
3.
→ Fig.
53
Screwing the retaining clips in place
Screw the enclosed retaining clips onto the work-
▶
top and carefully onto the appliance.
Ensure that the hob is at the same height as the
‒
worktop and the appliance does not slip.
Do not use an electric screwdriver.
‒
→ Fig.
45
Install the appliance for air extraction mode
For air extraction mode, use the seal and the
1.
acoustics filters.
Observe the instructions for the exhaust air pipe.
2.
→ Page 19
Securing the seal
Secure the enclosed seal on the flat duct elbow at
▶
a maximum of 5 mm from the edge.
→ Fig.
48
Establishing the piping
Insert the flat duct elbow into the outlet opening
1.
on the rear of the appliance.
→ Fig.
49
If required, install additional piping elements.
2.
Inserting the appliance into the worktop cut-out
Ensure that the connection cable is connected to
1.
the appliance.
Carefully insert the appliance into the worktop cut-
2.
out.
→ Fig.
50
Screwing the retaining clips in place
Screw the enclosed retaining clips onto the work-
▶
top and carefully onto the appliance.
Ensure that the hob is at the same height as the
‒
worktop and the appliance does not slip.
Do not use an electric screwdriver.
‒
→ Fig.
45
Connecting the exhaust air pipe
Secure the exhaust air pipe to the flat duct bend.
1.
Establish the connection to the exhaust air open-
2.
ing.
Seal the joints appropriately.
3.
Aligning the appliance in the worktop cut-out
Use the enclosed spacers to adjust the circumfer-
1.
ential gap between the appliance and the worktop
to a uniform distance of 1.5 to 2 mm.
→ Fig.
44
Remove the spacers before sealing the join.
2.
Connecting the cables to the appliance
Connect one of the longer cables to the appliance
1.
and to any control knob.
→ Fig.
54
Ensure that the plugs snap into place in the sock-
2.
ets.
Inserting filters
Note: For circulating-air mode, insert the odour fil-
ters.
For air extraction mode, insert the acoustics filters.
Observe the filters' air flow direction.
1.
Insert two of the filters into the left and right of the
2.
appliance, and slide them forwards.
→ Fig.
55
22
Insert the other filters into the left and right of the
3.
appliance.
→ Fig.
56
Inserting grease filters
Insert the grease filter.
▶
→ Fig.
57
Positioning the ventilation grille
Position the ventilation grille.
▶
→ Fig.
58
Establishing the connection to the power
supply
Observe the connection data on the rating plate.
1.
For 3 N, connect the cable to the mains socket in
2.
accordance with the figure.
→ Fig.
59
For 2 N, connect the cable to the mains socket in
3.
accordance with the figure.
→ Fig.
60
For 1 N, connect the cable to the mains socket in
4.
accordance with the figure.
→ Fig.
61
For 2 L/2 N, connect the cable to the mains
5.
socket in accordance with the figure.
→ Fig.
62
Note the colours of the cables.
6.
– BN: Brown
– BU: Blue
– GN/YE: Yellow and green
– BK: Black
– GY: Grey
If required, arrange the supplied wire end ferrules
7.
differently depending on the type of connection.
To connect two cables, if required, use a wire end
8.
ferrule.
Shorten the wires.
‒
Remove the insulation.
‒
Checking the function
Switch on the appliance.
1.
If , or lights up, the appliance is not
2.
connected correctly.
→ "Checking and correcting the electrical connec-
tion", Page 22
If no faults appear in the appliance's display, use
3.
the operating instructions to check that the ventila-
tion is working.
Checking and correcting the electrical connection
Disconnect the appliance from the power supply.
1.
Check whether the connection to the appliance
2.
(fig. 4) and the building-side connection (fig. 8)
correspond to the connection diagram in these in-
stallation instructions.
→ "Preparing the electrical connection", Page 19
→ "Establishing the connection to the power sup-
ply", Page 22
For 3 N, observe the following figure.
3.
→ Fig.
63
For 2 N, observe the following figure.
4.
→ Fig.
64
For 1 N, observe the following figure.
5.
→ Fig.
65
Sealing crevices
Requirement: You must carry out a function test be-
fore sealing the joint.