Electrical Connection - Electrolux KIC844I Montage- Und Gebrauchsanweisungen

3. Installation
Both electric and mechanical installation must be carried
out by specialised personnel.
The electrical appliance is designed to be built into a work top
with a thickness of 2-6 cm in the case of TOP installation; 2.5-
6 cm in the case of FLUSH installation.
The minimum distance between the hob and the wall must be
at least 5 cm in front, at least 4 cm on the sides and at least
50 cm from overhead wall units.
NB = The recommended distances are given as examples:
when planning the spaces, the indications of the kitchen
manufacturer must be observed.

3.1 Electrical connection

Fig. 3
● Disconnect the device from the electric power supply. ●
Installation must be carried out by professionally qualified
personnel with knowledge of the regulations in force for
installation and safety. ● The manufacturer denies all liability
to persons, animals or property if the guidelines provided in
this chapter are not followed. ● The power cable must be long
enough to allow the hob to be removed from the worktop. ●
Make sure that the voltage on the serial number data plate on
the bottom of the device corresponds to that of the domestic
environment where it will be installed. ● Do not use extension
leads. ● The earth power cable must be 2cm longer than the
other cables. ● If the electrical appliance is not supplied with a
power cable, use one with a minimum conductor diameter of
2
2.5 mm for power up to 7200 Watt; for higher power levels,
the diameter must be 4 mm
reach 50°C above room temperature anywhere along the
cable. ● The appliance is intended for permanent connection
to the power supply.
Note: to connect the appliance using the optional single
phase connection the existing cable must be removed
and replaced with another type (not supplied) having the
following specifications:
single phase connection: H05V2V2-F 3G4 cable
Fig. 3a
Please note! Before reconnecting the circuit to the mains
power supply, make sure that it is working correctly, always
check that the power cable is correctly installed.
Please note! The interconnection cable must be replaced by
the authorised technical support service or by a person with
similar qualifications.
Note : the product is equipped with a Power Limitator
function, which allows a maximum power limit to be set
The limit must be set at the time of the product's connection to
the electrical network or when the electrical network itself is
reconnected (within the following 2 minutes). For the Power
Limitation setting sequence, see the Operation section of
this manual.
2
. ● The temperature must not
3.2 Mounting
Before starting the installation:
• After unpacking the product, check that it has not
been damaged during transport and in the event of
problem, please contact the reseller or the Customer
support service before installing it.
• Check that the product is the right size for the installation
area.
• Check for accessories (e.g. bags containing screws,
warranty certificates, etc.) inside the packaging (placed
there for transport reasons). Remove and keep them
safe, if present.
• Also check that there is a power socket near the
installation area.
Preparing the cabinet for installation:
- The product cannot be installed above cooling appliances,
dishwashers, heaters, ovens, washing machines and
dryers.
- Create the cut-outs in the cabinet before inserting the hob
and carefully remove any shavings or sawdust.
IMPORTANT: use a single-component adhesive sealant (S),
which withstands temperatures up to 250°; before
installation, thoroughly clean the surfaces to stick and
eliminate any substance that may compromise adhesion,
(e.g. release agents, preservatives, fats, oil, dust, traces
of old adhesives, etc.); the adhesive should be uniformly
spread all around the outside of the frame; after sticking,
leave the adhesive to dry for about 24 hours.
Fig. 1b
CAUTION! Failure to install screws and fasteners in
accordance with these instructions may result in electrical
hazards.
Note: to ensure the correct installation of the product, it is
recommended to tape the pipes using an adhesive with the
following characteristics:
- soft elastic PVC film, with an acrylic-based adhesive
- compliant with DIN EN 60454 regulations
- flame retardant
- excellent resistance to wear
- resistant to temperature fluctuations
- can be used at low temperatures
89