Maintenance And Service; Maintenance And Cleaning; After-Sales Service And Application Service - Bosch UniversalTacker 18V-14 Originalbetriebsanleitung

material edge. The accessory is only suitable for the
UniversalTacker 18V-14.
– With the paper tacker (13), you can tack together up to
80 sheets.
– With the spacer (13), you can set an equal distance of
1 cm to 11 cm between the fastener and the material
edge using six settings.
Note: To load the magazine (9), you have to remove the pa-
per tacker/spacer (13) from the power tool.
Tacking Paper (see figures B1–B2)
Note: Tacker staples are stronger than standard staples and
are therefore more difficult to remove from the paper.
Recommended
staple length
6 mm
8 mm
10 mm
12 mm
– Set the impact force to the highest level.
– Insert a suitable staple strip (14).
– Click the lugs of the paper tacker/spacer (13) one by one
into the slots for the paper tacker (11) on the power tool.
Please note that only slot 1 is suitable for tacking paper.
– Place the stack of paper in the paper tacker/spacer (13)
and position the tacker head over the paper surface to be
tacked.
– Firmly press the power tool down until the tacker
head (1) is fully pushed in.
– Maintain the contact pressure and press the trigger (2).
– Once the staple has been completely driven in, release
the trigger (2) and lift the tacker head (1) from the stack
of paper.
Tacking at equal distances from the material edge
(see figures C1−C2)
Note: For tacking at equal distances, the spacer (13) must
be clicked into the slots (10) on the power tool.
Slots 2–7 (10)
Slot 2
Slot 3
Slot 4
Slot 5
Slot 6
Slot 7
– Insert a suitable staple strip (14) or nail strip (15).
– Click the lugs of the paper tacker/spacer (13) one by one
into a slot (10) on the power tool, which specifies the ap-
propriate distance from the material edge.
Please note that slot 1 is not suitable for tacking at equal
distances.
– Push the flexible underside of the paper tacker/spacer
(13) towards the power tool until it engages.
Bosch Power Tools
– Guide the power tool flat over the workpiece until the
workpiece edge reaches the front edge of the paper
tacker/spacer (13).
– Firmly press the power tool down until the tacker
head (1) is fully pushed in.
– Maintain the contact pressure and press the trigger (2).
– Once the staple/nail has been completely driven in, re-
lease the trigger (2) and push the tacker head (1) along
the workpiece edge.
– Position the next staple or nail.

Maintenance and Service

Number of sheets

Maintenance and Cleaning

2
(80 g/m paper)
Remove the battery from the power tool before carry-
u
2–20
ing out work on the power tool (e.g. maintenance,
10–40
changing tool, etc.). The battery should also be re-
20–60
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
30–80
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.

After-Sales Service and Application Service

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
Distance
UB 9 5HJ
1 cm
At www.bosch-pt.co.uk you can order spare parts or arrange
3 cm
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
5 cm
E-Mail: boschservicecentre@bosch.com
7 cm
You can find further service addresses at:
9 cm
www.bosch-pt.com/serviceaddresses
11 cm
Transport
The recommended lithium-ion batteries are subject to legis-
lation on the transport of dangerous goods. The user can
transport the batteries by road without further require-
ments.
When shipping by third parties (e.g.: by air transport or for-
warding agency), special requirements on packaging and la-
belling must be observed. For preparation of the item being
English | 17
1 609 92A 6V3 | (09.09.2022)