Maintenance And Inspection - HIKOKI G 3612DVE Bedienungsanleitung

Seite von 288

/ 288
Inhalt
Inhaltsverzeichnis
Lesezeichen

Inhaltsverzeichnis

Verfügbare Sprachen

English

*4 WARNING

Before use, be sure to tighten the wheel nut with the

included wrench.

Failure to tighten could result in the wheel nut

loosening when the brake is activated during a stop.

NOTE

The wheel washer is speciﬁ cally for this product. Do

not use it for any other product.

*5 About the mode change function

With Auto mode, you can lower noise and vibration by

lowering the maximum number of revolutions while in a

no-load state.

While in Auto mode, the number of revolutions will be

raised if the load becomes greater during operation.

On the other hand, the number of revolutions will be

lowered if the load decreases during operation.

NOTE

○ To enable mode changes, pull the switch once after

installing the battery.

○ The set mode remains set even if the power is turned oﬀ .

○ Do not give a strong shock to the switch panel or break it.

It may lead to a trouble.

<G3612DVE, G3613DVE, G3613DVF, G3615DVE, G3615DVF>

Pressing the Auto mode switch will change the

operating mode back and forth between Auto mode and

Transmission mode.

With Transmission mode, the grinder's number of

revolutions can be set at one of six levels using the dial.

When operating in Transmission mode, the set number

of revolutions will be maintained regardless of changes

in load.

Set the mode and dial according to work application.

(Table 3)

Number of

Revolutions (min-

Status

G3612DVE

G3615DVE

G3613DVE

G3615DVF

G3613DVF

3200

3900

5300

7400

8600

10000

Auto L

5500

Auto H

10000

Auto L: No-load

Auto H: During operation

<G3613DE, G3613DF>

Pressing the Auto mode switch will change the operating

mode back and forth between Auto mode and Full-Speed

mode. In Full-Speed mode, the number of revolutions is

controlled so that it always remains constant.

Set the mode according to work application.

Table 3

)

Use

3200

Grinding stainless

steel

3600

Rust or paint removal

4600

Grinding, ﬁ nishing

5600

Rough grinding,

7200

cutting

8000

Light work, Standby

5500

state

Grinding, cutting

8000

*6 Do not expose directly your eye to the light by looking

into the light.

If your eye is continuously exposed to the light, your eye

will be hurt.

Wipe oﬀ any dirt or grime attached to the lens of the LED

light with a soft cloth, being careful not to scratch the

lens.

Scratches on the lens of the LED light can result in

decreased brightness.

*7 Grinding angle and grinding method

Press down the machine evenly on the surface and

move back and forth so that the surface of the workpiece

does not become too hot.

Rough grinding: position the machine at an angle of

15°–30° for the best working results.

When the grinding stone is new, its corner may dig in

when it is pushed forward, so pull back during use.

(Fig. 14-a)

Once the wheel edge is worn, the workpiece can be

ground in both directions. (Fig. 14-b).

*8 Cutting work

Always work against the run of the disc. Otherwise there

is the danger of the machine kicking back from the cut

out of control. Guide the machine evenly at a speed

suitable for the material being processed. Do not tilt,

apply excessive force or sway from side to side.

LED LIGHT WARNING SIGNALS

This product features functions that are designed to protect

the tool itself as well as the battery. While the switch is

pulled, if any of the safeguard functions are triggered

during operation, the LED light will blink as described in

Table 4. When any of the safeguard functions are triggered,

immediately remove your ﬁ nger from the switch and follow

the instructions described under corrective action.

Safeguard

LED Light Display

Function

Overburden

On 0.1 second/

Protection

oﬀ 0.1 second

Kickback

Protection

On 0.5 second/

Temperature

oﬀ 0.5 second

Protection