Optional Accessories - Makita CL117FD Betriebsanleitung

1. To remove the rear cover, push it in the direction of
the arrow.
► Fig.40: 1. Rear cover
2.
Slide the built-in battery halfway. Disconnect the
lead wires from the battery by slightly moving back the
battery while pressing the connector in the direction of
arrow as shown in the figure.
► Fig.41: 1. Connector 2. Lead wires
3. Then slide the battery unit out completely.
► Fig.42: 1. Battery unit
4.
Put the removed battery unit in a carton box so
that it is not circuit-shorted.
Installing replacement battery
To install the replacement battery, follow the removal
procedure in reverse.
CAUTION:
Route the lead so that it is com-
pletely stored inside the cleaner before putting
the rear cover back in the original position. Failure
to do this may damage the lead.
► Fig.43
After installing the battery (see "SPECIFICATIONS"),
charge the battery before use.

OPTIONAL ACCESSORIES

CAUTION:
These accessories or attachments
are recommended for use with your Makita appli-
ance specified in this manual. The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or attachment
for its stated purpose.
If you need any assistance for more details regard-
ing these accessories, ask your local Makita Service
Center.
• Extension wand
• Nozzle
• Nozzle for carpet
• Shelf brush
• Corner nozzle
• Round brush
• Flexible hose
• Filter
• Prefilter
• High performance filter
• HEPA filter
• Seat nozzle
• Crevice nozzle
• Wall mount for cordless cleaner
• Cyclone attachment
• Makita genuine battery and charger
NOTE: Some items in the list may be included in the
appliance package as standard accessories. They
may differ from country to country.
Cyclone attachment
► Fig.44: 1. Release button 2. Hook 3. Extension
wand 4. Cyclone attachment 5. Suction inlet
About the cyclone attachment
Using the cleaner with the cyclone attachment installed
reduces the amount of dust that enters the capsule,
which helps to prevent the suction force from weaken-
ing. In addition, cleaning after use is also simple.
CAUTION:
Always be sure that the appliance
is switched off before carrying out any work on
the appliance.
CAUTION:
Clean the mesh filter of the
cyclone attachment and the filters of the cleaner
unit when they become clogged. Continued use in
the clogged condition may result in heating or smoke.
NOTICE:
When the cyclone attachment is
attached, do not use the cleaner in a horizontal
or upward facing position. Doing so may cause the
mesh filter to become clogged.
NOTICE:
Always use the cleaner with the filters
installed, even when using the cyclone attach-
ment. Using the cleaner without the filters installed
may result in a motor malfunction.
NOTE: Check that the cyclone attachment, cleaner,
and extension wand are locked properly before use.
NOTE: Empty the dust case of the cyclone attach-
ment and the capsule of the cleaner when dust has
accumulated. Continued use will result in weakened
suction force.
NOTE: You can also use the cyclone attachment with-
out lock function.
NOTE: To install or remove the cyclone attachment,
refer to the section "Installing and removing cleaner
attachments".
Disposing of dust
When dust has accumulated up to the full line of the
dust case, follow the procedure below and dispose of
the dust.
1.
Hold the dust case firmly, press and hold the two
buttons, and remove the dust case.
► Fig.45: 1. Full line 2. Dust case 3. Button (two
locations) 4. Mesh filter
2. Dispose of the dust inside the dust case and
remove any dust and powder adhered to the surface of
the mesh filter.
3.
Insert the dust case all the way until the two but-
tons lock with a click.
► Fig.46: 1. Dust case 2. Button (two locations)
CAUTION:
Be careful not to trap finger(s)
between the dust case and cyclone body when
reassembling.
16 ENGLISH