Optional Accessories - Makita DVC861L Betriebsanleitung

2. Set the rails on the tool box along the grooves on the
housing. (Fig. 20)
3. Close the battery cover and apply the lock.
The tool box is convenient for carrying batteries,
extension cord, pipe, or cuffs. (Fig. 21)
Connecting the hose
CAUTION:
• Never force the hose for bending or stamp it. Never
move the cleaner by a hose. Forcing, stamping and
pulling the hose may cause a breakage or deformation
of the hose.
• When picking up large wastes such as planer carvings,
concrete dusts or similar other than small wastes, use
the 38 mm inner diameter hose (optional accessory).
Using the 28 mm inner diameter hose (optional
accessory) may cause a hose stuffing and damage.
Insert the hose onto the mounting port of the tank and turn
it clockwise until it locks. (Fig. 22)
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off, unplugged,
and the battery cartridge is removed before attempting
to perform inspection or maintenance.
Storage of power supply cord (Fig. 23)
You can wind up the power supply cord around the tool
box.
Storage of accessories (Fig. 24)
The pipes can be placed into the pipe holder when not
using the cleaner for a short time. (Fig. 25)
The hose can be stored around the tool by connecting
each ends. (Fig. 26)
Cleaning
CAUTION:
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
Cleaning of cloth filter
Only for the cloth filter model
Clogged cloth filter causes poor suction performance.
Clean out the cloth filter from time to time.
To remove dust or particles adhering to the cloth filter,
shake the frame bottom quickly several times. (Fig. 27)
Cleaning of powder filter (HEPA) and
prefilter
Only for the powder filter model
Clogged powder filter, prefilter and damper cause poor
suction performance.
Clean out the filters and dampers from time to time.
To remove dust or particles adhering to the filters, shake
the frame bottom quickly several times.
Occasionally wash the powder filter in water, rinse and dry
thoroughly in the shade before use. Never wash filters in a
washing machine. (Fig. 28)
14
NOTE:
• Do not rub and scratch the powder filter, the prefilter or
the damper with hard objects such as a brush and a
paddle.
• The filters wear out in course of time. It is
recommended to have some spares for them.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers, always
using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Makita genuine battery and charger
• Hose
• Front cuffs (22, 24, 38)
• Straight pipe
• Corner nozzle
• Round brush
• Powder filter,HEPA (for dry dust)
• Damper
• Prefilter
• Nozzle assembly
• Bent pipe
• Polyethylene bag
• Water Filter (option for the cloth filter model)
• Paper pack
• Holder set
NOTE:
• Some items in the list may be included in the tool
package as standard accessories. They may differ from
country to country.
Noise
The typical A-weighted noise level determined according
to IEC60335-2-69:
Sound pressure level (L
Uncertainty (K): 2.5 dB (A)
The noise level under working may exceed 80 dB (A).
• The declared noise emission value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
• The declared noise emission value(s) may also be
used in a preliminary assessment of exposure.
WARNING:
• Wear ear protection.
• The noise emission during actual use of the power
tool can differ from the declared value(s)
depending on the ways in which the tool is used
especially what kind of workpiece is processed.
• Be sure to identify safety measures to protect the
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
ENG905-1
): 75 dB (A)
pA
ENG907-1