Herunterladen Inhalt Inhalt Diese Seite drucken

Charging Process - DeWalt XR LI-ION DCF813 Originalanweisungen

10,8 v akku-schlagschrauber
Vorschau ausblenden Andere Handbücher für XR LI-ION DCF813:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 16
EN GLI SH
• NEVER attempt to connect 2 chargers together.
• The charger is designed to operate on
standard 230V household electrical power.
Do not attempt to use it on any other
voltage. This does not apply to the vehicular
charger.
SAVE THESE INSTRUCTIONS
Chargers
The DCB100 and DCB105 chargers accept 10.8 V
Li-Ion batteries.
These chargers require no adjustment and are
designed to be as easy as possible to operate.
Charging Procedure (fi g. 2)
1. Plug the charger (k) into an appropriate outlet
before inserting battery pack.
2. Insert the battery pack (f) into the charger.
The red (charging) light will blink continuously
indicating that the charging process has started.
3. The completion of charge will be indicated by
the red light remaining ON continuously. The
pack is fully charged and may be used at this
time or left in the charger.
NOTE: To ensure maximum performance and life of
Li-Ion batteries, charge the battery pack fully before
first use.

Charging Process

Refer the table below for the state of charge of the
battery pack.
State of charge
charging
fully charged
hot/cold pack delay
replace battery pack
Hot/Cold Pack Delay
When the charger detects a battery that is too hot
or too cold, it automatically starts a Hot/Cold Pack
Delay, suspending charging until the battery has
reached an appropriate temperature. The charger
then automatically switches to the pack charging
mode. This feature ensures maximum battery life.
LI-ION BATTERY PACKS ONLY
Li-Ion batteries are designed with an Electronic
Protection System that will protect the battery
against overloading, overheating or deep discharge.
The tool will automatically turn off if the Electronic
Protection System engages. If this occurs, place the
Li-Ion battery on the charger until it is fully charged.
30
Important Safety Instructions for All
Battery Packs
When ordering replacement battery packs, be sure
to include catalog number and voltage.
The battery pack is not fully charged out of the
carton. Before using the battery pack and charger,
read the safety instructions below. Then follow
charging procedures outlined.
• Do not charge or use battery in explosive
• Never force battery pack into charger. Do
• Charge the battery packs only in D
• DO NOT splash or immerse in water or other
• Do not store or use the tool and battery
– – –
–––––––––––
–– – –– –
•••••••••••
SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION
(Li-Ion)
• Do not incinerate the battery pack even if it
READ ALL INSTRUCTIONS
atmospheres, such as in the presence of
flammable liquids, gases or dust. Inserting
or removing the battery from the charger may
ignite the dust or fumes.
not modify battery pack in any way to fit
into a non-compatible charger as battery
pack may rupture causing serious personal
injury.
chargers.
liquids.
pack in locations where the temperature
may reach or exceed 40 ˚C (105 ˚F) (such as
outside sheds or metal buildings in summer).
WARNING: Never attempt to open the
battery pack for any reason. If battery
pack case is cracked or damaged, do
not insert into charger. Do not crush,
drop or damage battery pack. Do not
use a battery pack or charger that has
received a sharp blow, been dropped,
run over or damaged in any way (i.e.,
pierced with a nail, hit with a hammer,
stepped on). Damaged battery packs
should be returned to service centre for
recycling.
CAUTION: When not in use, place
tool on its side on a stable surface
where it will not cause a tripping or
falling hazard. Some tools with large
battery packs will stand upright on the
battery pack but may be easily knocked
over.
is severely damaged or is completely worn
out. The battery pack can explode in a fire.
WALT
E

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Xr li-ion dcf815Dcf815

Inhaltsverzeichnis