EINHELL TP-RO 18 Li BL Originalbetriebsanleitung Seite 23

6.3 Adjusting the routing depth (Fig. 12)
•
Place the machine on the workpiece.
•
Undo the lock nut (11) and the clamp lever
(19).
•
Slowly move the machine downwards and
press the depth adjuster (12) until the cutter
makes contact with the workpiece.
•
Tighten the clamp lever (19).
•
Set the precision adjustment device (8) ac-
cordingly to 0.
•
Set the end stop (13) so that the depth stop
(14) lies above the lowest set end stop (13).
•
Press the depth adjuster (12) to lower the
depth stop (14) until it touches the end stop
(13). Then tighten the lock nut (11) and re-
lease the clamp lever (19).
•
Set the pointer (10) to the zero point on the
scale (9).
•
Undo the lock nut (11). Push up the depth
stop (14) until the pointer (10) shows the re-
quired routing depth on the scale (9). Retigh-
ten the lock nut (11).
•
Test the setting by performing a test cut on a
piece of scrap material.
•
Now the routing depth can be finely adjusted.
Begin by turning the precision adjustment
device (8) to the required dimension.
Turn the precise adjustment device (8) coun-
ter-clockwise:
The routing depth is raised
Turn the precision adjustment device (8)
clockwise:
The routing depth is lowered
Turning the precision adjustment device (8) by
one increment is equivalent to changing the rou-
ting depth by 0.1mm; one full turn is equivalent to
1mm.
6.4 Routing
•
To avoid damage to the router, make sure
there are no foreign objects attached to the
workpiece.
•
Hold both of the router's handles (7).
•
Place the cordless router on the workpiece.
•
Set the routing depth as explained in section
6.3.
•
Select the speed as explained in section 6.2
and switch on the equipment (see section
6.1)
•
Test the equipment's settings on a scrap pie-
ce of material.
•
Let the equipment reach full speed. Only then
Anl_TP-RO_18_Li_BL-Solo_SPK13.indb 23
GB
should you lower the cutter to its working
height and lock the equipment with the clamp
lever (19).
Cutting direction: The cutting tool turns clock-
wise. To avoid accidents you must always cut
against the direction in which the tool turns (Fig.
13).
Feed speed: It is very important to machine the
workpiece at the correct feed speed. We recom-
mend that before you machine the actual workpi-
ece, you carry out several trial cuts on a scrapped
piece of the same material. This is the easiest way
to fi nd the best working speed for the workpiece.
Feed speed too low:
The cutter might overheat. If you are cutting in-
fl ammable material such as wood, the workpiece
might ignite.
Feed speed too high:
The cutter might become damaged. Cutting quali-
ty: Rough and uneven.
Allow the cutter to come to a complete standstill
before removing the workpiece or putting down
the router.
6.5 Step-by-step routing
Step-by-step routing makes sense when proces-
sing hard material and performing deep cuts.
•
Adjust the end stops as explained in section
5.7.
•
To carry out a routing job in several steps you
must then set the routing depth as explained
in section 6.3 before turning the end stop
(13) so that the depth stop (14) lies above the
highest end stop (13).
•
Now perform a cut in this setting. When the
first cut is completed, set the end stop (13) so
that the depth stop (14) lies above the middle
end stop. Now perform a cut in this setting as
well.
•
Finally, set the lowest end stop and complete
the cutting.
6.6 Cutting circles with the compass point
(26)
Proceed as follows to cut circles around a center-
point:
•
Fit and adjust the compass point (26) as exp-
lained in section 5.4.
•
Place the compass point (26) on the center-
point of the circle you want to cut and press it
- 23 -
11.07.2022 08:42:30