EINHELL TP-RO 18 Li BL Originalbetriebsanleitung Seite 22

tive gloves at all times when handling cutting
tools.
•
To make it easier to change the cutter, re-
move the cordless routing unit (1) from the
respective insert as described in section 5.5
•
Cutters with a shaft diameter of 6 mm and 8
mm can be used in the cordless router. Most
cutters are available in both sizes.
•
You can use cutters made of the following
materials:
- HSS - suitable for cutting softwood
- TCT - suitable for cutting hardwood, particle
board and plastic
•
Select the appropriate cutting tool for the job
in hand.
•
When using the cutters for the first time:
Remove the plastic packaging from the cutter
heads.
•
Clean the nut, clamp and shaft of the cutter
before fitting it.
•
Undo the clamp nut (6) using the two open-
ended wrenches (23).
•
If a cutter is already fitted in the clamp
(24/25), remove it.
•
Select the appropriate cutting tool (f) for the
job in hand.
•
Select the appropriate clamp (24/25) for the
cutter you want to use.
•
Now insert the clamp (24/25) in the cutting
spindle (Fig. 8).
•
Refit the clamp nut (6) (Fig. 9).
•
Guide the cutter shaft into the clamp (Fig. 10).
•
While holding the spindle lock (5) in pressed
position, screw the clamp nut (6) hand-tight
(Fig. 10).
•
Notice!
The spindle lock is not allowed to be used for
tightening with the open-ended wrench (23)!
•
Tighten the clamp nut (6) using the two open-
ended wrenches (23).
•
The cutter must be inserted into the clamp
(24/25) by at least 20mm.
•
Before you use the equipment, check that the
cutting tool is secure and runs true.
5.7 Adjusting the end stops (Fig. 12/Item 13)
The end stops (13) can be adjusted in height
according to requirements. To do so, use a hex
key to turn the screw on the end stop (13) to the
required stop height.
Warning! Remove the setting and assembly
tools again before starting the machine.
Anl_TP-RO_18_Li_BL-Solo_SPK13.indb 22
GB
6. Operation
•
Never use a low-quality or damaged cutter.
Use only cutting tools with a shaft diameter of
6 mm or 8 mm. The cutters must also be desi-
gned for the respective idling speed.
•
Secure the workpiece so that it cannot be
thrown through the air as you work on it. Use
clamps or a vise.
•
Never cut over metal parts, screws, nails etc.
6.1 On/Off switch (Fig. 1/Item 3)
For safety reasons, the cordless router is
equipped with a safety lock-off .
•
To switch on, press the unlock/lock button (2).
The LED lamp (29) will begin to shine by way
of confirmation.
•
Now press the On/Off switch (3) within the
next 10 seconds.
•
If the On/Off switch is not pressed for longer
than 10 seconds, the LED lamp (29) will go
out and the equipment cannot be switched
on.
•
To switch off, press either the unlock/lock but-
ton (2) or the On/Off switch (3).
6.2 Speed control (Fig. 12/Item 4)
The most suitable speed depends on the material
you want to cut and on the diameter of the cut-
ter. Use the speed control switch (4) to select a
speed between 10,000 and 30,000 min
choose from 6 diff erent switch positions.
The speeds in the various switch positions
are as follows:
Switch position 1: approx. 10,000 min
speed)
Switch position 2: approx. 14,000 min
Switch position 3: approx. 19,000 min
Switch position 4: approx. 22,000 min
Switch position 5: approx. 25,000 min
Switch position 6: approx. 30,000 min
speed)
To increase the speed:
Move the speed controller (4) in the plus direction.
To decrease the speed:
Move the speed controller (4) in the minus direc-
tion.
- 22 -
. You can
-1
(minimum
-1
-1
-1
-1
-1
(maximum
-1
11.07.2022 08:42:30