Before Starting The Equipment - Scheppach HS105 Originalbetriebsanleitung

Noise values
The total noise values determined in accordance with
EN 61029.
sound pressure level L
pA
uncertainty K
pA
sound power level L
WA
uncertainty K
WA
Wear hearing protection.
The effects of noise can cause a loss of hearing. Total
vibration values (vector sum - three directions) deter-
mined in accordance with EN 61029.

7. Before starting the equipment

• The equipment must be set up where it can stand
securely, i.e. it should be bolted to a workbench, a
universal base frame or similar.
• All covers and safety devices have to be properly fit-
ted before the equipment is switched on.
• It must be possible for the blade to run freely.
• When working with wood that has been processed
before, watch out for foreign bodies such as nails or
screws, etc.
• Before you press the ON/OFF switch check that the
saw blade is fitted correctly. Moving parts must run
smoothly.
• Before you connect the equipment to the power sup-
ply make sure the data on the rating plate are dentical
to the mains data.
• Connect the machine to a properly installed protec-
tive contact socket, with at least 16A circuit breaker.
8. Attachment
Important. Pull out the power plug before carrying
out any maintenance, resetting or assembly work on
the circular saw!
Place all parts supplied on a flat surface. Grouping
equal parts.
Note: If compounds with a bolt (round head / or hexa-
gon), hex nuts and washers are backed up, the washer
must be fitted under the nut.
Insert screws each from outside to inside. Secure con-
nections with nuts on the inside.
Note: Tighten the nuts and bolts during assembly only
to the extent that they can not fall down.
If you tighten the nuts and bolts prior to final assembly,
final assembly can not be performed.
8.1 Frame assembly, Fig. 5/6/7
1. Fix the four legs (17) with the bolts (g) and nuts (h)
to the struts (20+21).
m Warning!
The top struts are equipped with a slot for fixing
them to the table!
Ensure that markings A and B are always opposite
each other.
2. Now loosely fix the lower struts to the legs using the
bolts (g) and nuts (h) (Fig. 5).
3. Now place the rubber feet (22) on the legs (Fig. 6).
4. Then mount the entire saw on the frame by fixing
the hexagon head bolts and the nuts in the corners
(Fig. 7).
5. Afterwards, tighten all bolts and nuts to the frame.
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
8.2 Hand wheel assembly, Fig. 8
1. Place the washer (e) on the bolt (a).
2. Then place the bolt on the handle (b) and the
3. Fix the whole assembly to the hand wheel (8) and
92,6 dB(A)
3 dB
8.3 Riving knife set-up (Fig. 9/10/11)
105,6 dB(A)
3 dB
1.
2.
3.
4.
5.
8.4 Saw blade guard assembly (Fig. 12)
1. Place the saw blade guard (2) including the bolt (24)
2. Do not tighten the bolt (24) too much; the saw blade
3. Place the extraction hose (3) on the extraction adap-
4. Disassembly takes place in reverse order.
8.5 Saw blade assembly/replacement (Fig.
9/12/13)
1. Warning! Disconnect the mains supply and wear
2. Disassemble the saw blade guard (2) (Fig. 12).
3. Remove the table insert (6) (Fig. 9).
4. Loosen the nut by placing the open-ended spanner
5. Warning! Turn the nut in the rotational direction of
6. Remove the outer flange and pull the old saw blade
7. Carefully clean the saw blade flange with a wire
8. Insert the new saw blade in reverse order and
9. Attach the table insert (6) and the saw blade guard
10. Before working with the saw again, check the func-
washer (c) on the bolt.
secure it with the hex-nut (d).
m Warning! Disconnect the mains cable!
The set-up of the riving knife (6) must be che-
cked before each use.
Set the saw blade (5) to the max. cutting depth, put
it in the 0° position and lock it. .
Remove the table insert (6) (Fig. 8)
m Warning! For transport reasons, the riving
knife (6) was fixed in the lower position be-
fore initial commissioning. Only work with the
machine if the riving knife (6) is in the upper
position. Fitting the riving knife (6) in the upper
position is as follows:
Loosen the locking handle (23) and push the riving
knife (6) in the upper position (Fig. 9).
The gap between the saw blade (5) and the riving
knife (6) should be a maximum of 5 mm (Fig. 10).
Re-tighten the mounting screw (23) and fix the
table insert (6).
on the riving knife (4) from above so that the bolt is
tight in the slot of the riving knife (4).
guard (2) must be able to move freely.
ter on the rear of the machine and on the extraction
nozzle of the saw blade guard (2).
Warning!
Before starting to saw, lower the saw blade
guard (2) on to the work piece.
safety gloves.
(f) on the nut and countering with another open-
ended spanner (f) on the flange (Fig. 13).
the saw blade.
from the inner flange, with a diagonally downwards
movement.
brush before fixing the new saw blade.
tighten it.
Warning! Observe the rotational direction; the
teeth have to point in the direction of rotation,
i.e. forwards.
(2) again and set them.
tionality of the guards.
25 І 128