Control Via The App Undok - Monacor PA-1200IRD Einbau- Und Bedienungsanleitung

The icon will also appear on the display in the
standby mode and, in addition, the alarm
time set will be indicated next to the icon.
5) If the module is in the standby mode, it will
be activated at the alarm time and the alarm
bell icon will flash on the display.
To deactivate the alarm, press the but-
ton ALARM: The module will return to the
standby mode.
Note: If the alarm is not deactivated, the module
will automatically return to the standby mode after
20 minutes.
The snooze function offers the possibility to
stop and resume the alarm: After the alarm,
press the button SLEEP to switch the module
to standby so that the alarm will start again
after 5 minutes. To change the alarm interval,
press the button SLEEP repeatedly:
5, 10, 15 or 30 minutes
6) In the standby mode, the button ALARM
can be used to switch the alarms on or off.
Press the key repeatedly to select the setting
desired:
Setting
both alarms Off
alarm 1 only On
alarm 2 only On
both alarms On

6.8 Control via the app UNDOK™

The app UNDOK™ will allow you to operate the
module from a smartphone or tablet computer.
The app is available for devices using the operat-
ing system "Android" or "iOS" and is available
for free download from the corresponding app
store.
Notes:
1. The app is provided by a third party and is not
covered by the warranty of MONACOR INTERNA-
TIONAL. In case of any problems, please contact
the provider of the app!
2. The app may have been further developed in the
meantime; therefore, the details listed here may
no longer be up to date.
1) Download the app on your smartphone / tab-
let and open the app. When a prompt from
the app appears requesting permission to
access controllable devices in the network,
Indication on the display
no bell icon
bell icon 1
bell icon 2
bell icons 1 and 2
permission must be granted; otherwise, con-
trol via the app will not be possible.
2) When the app has been opened, the start
screen will show an overview of the available
devices. The module will be displayed with
☞
its "Friendly Name" = name of the module
in the network (
➜ Info ➜ Friendly Name
If the module is not on the list, check
the network settings and set up the module
again if necessary. Alternatively, you can try
to use the setup wizard of the app in order to
connect the module to the network. In case
of any problems, please refer to the informa-
tion in the text box at the end of this chapter.
3) Tap the name of the module to open the
control page for the module. The user inter-
face of the page is self-explanatory and can
be operated intuitively. "SOURCE", for ex-
ample, is used to select the operating mode
and "BROWSE" to select one of the options
available for the mode selected. When you
tap the icon in the radio mode, the stor-
age locations will be shown: The current sta-
tion can be saved (tap the plus sign behind
the storage location number) and recalled.
"NOW PLAYING" will show full information
about the current replay. Setup options for
the module can be called up in the taskbar
at the top of the screen via the icon or
(depending on the app version).
4) To return to the overview, tap the arrow in
the taskbar at the top of the screen.
If control via the network fails to work, check
the following requirements:
– Make sure that the main device into which the
module has been installed is switched on.
– Make sure that the option
for
Keep network connected
made via the setup wizard or the corresponding
menu item in the menu "System settings"). This
way, the module will always maintain the connec-
tion to the network, even in the standby mode.
– Make sure that the smartphone / tablet and the
module are connected to the same network.
– Make sure that the router allows communication
between wireless LAN devices in the network.
If not, activate the corresponding setting on the
router.
menu "System settings"
).
has been selected
YES
(setting can be
45