1. Product information Fig. 1 Carrier rail AZURA® Click The carrier rail AZURA® Click is intended for mounting the following devices: Interface box (AZB00XA) Pressure control (AZG10) AZURA pH sensor (A70091-2) AZURA Organizer (A70085) Distribution box (AZS80SA) ...
Seite 5
Attaching AZURA® Click Process 1. Remove the protective foil from the carrier rail Fig. 2 Protective foil 2. Position the carrier rail flush with the back panel in 9 cm height. 3. To mount the carrier rail, press it strongly against the side panel Fig.
3. Attaching devices on AZURA® Click 3.1 Interface box, pressure control, pH sensor, Organizer & distribution box 3.1.1 Attaching device Note: Interface box, pressure control, pH sensor and distribu- tion box are supplied with a pre-installed mounting rail holder that can be used to mount the device to AZURA® Click. Prerequisite: AZURA®...
Seite 7
(AZS80SA) is attached to the carrier rail in the same way as for the devices in figure 4 to 7. Video: On the KNAUER YouTube channel you will find a short tutorial on how to attach and take off the AZURA® Organizer from the carrier rail: AZURA®...
Attaching devices on AZURA® Click 3.1.2 Taking off device Process 1. Pull the handle of the mounting rail holder down 2. Take off the device by tilting it upwards. Fig. 8 Taking off the device exemplified by the interface box AZURA®...
Attaching devices on AZURA® Click 3.2 Air sensor 3.2.1 Attaching air sensor Prerequisite: The metal rail has been removed (Fig. 9). AZURA® Click has been mounted. Process 1. Pull back the metal rail against the spring. 2. Take off the metal rail of the air sensor. Fig.
Fig. 10 Position of air sensor Video: On the KNAUER YouTube channel you will find a short tutorial on how to attach and take off the air sensor from the carrier rail: AZURA® Click with air sensor.
4. Repeat orders Name Article no. AZURA® Click A70089 Interface box AZB00XA Air sensor for 1/16” tubing A70092-1 Air sensor for 1/8” tubing A70093-1 Air sensor for 1/14” tubing A70083-1 AZURA® pH sensor A70091-2 Pressure control AZG10 Distribution box AZS80SA 5.
1. Produktinformation Abb. 1 Tragschiene AZURA® Click Die Tragschiene AZURA Click ist für die Befestigung folgender Geräte vorgesehen: Interface Box (AZB00XA) Drucksensor (AZG10) AZURA pH-Sensor (A70091-2) AZURA Organizer (A70085) Verteilerbox (AZS80SA) Air Sensor (A70092-1, A70093-1, A70083-1) ...
Seite 15
AZURA® Click anbringen Ablauf 1. Die Schutzfolie von der Tragschiene abziehen. Abb. 2 Entfernen der Schutzfolie 2. Die Tragschiene bündig mit der Rückseite in 9 cm Höhe positionieren. 3. Die Tragschiene fest gegen die Seitenwand drücken. Abb. 3 Position der Tragschiene Hinweis: Für eine optimale Haftung beschweren Sie die Trageschiene für mindestens 1 h nicht.
3. Geräte an AZURA® Click anbringen 3.1 Interface Box, Druck-, pH-Sensor, Organizer & Verteilerbox 3.1.1 Gerät anbringen Hinweis: Interface Box, Verteilerbox sowie Druck- und pH-Sensor werden mit einem vorinstallierten Tragschienenhalter geliefert, mit dem das Gerät an AZURA® Click befestigt wird. Voraussetzung: AZURA®...
Seite 17
Weise wie bei den Geräten in den Abbildungen 4 bis 7 an der Tragschiene befestigt. Video: Auf dem KNAUER YouTube-Kanal finden Sie ein kurzes Tutorial, wie Sie den AZURA® Organizer an AZURA® Click anbringen und abnehmen: AZURA® Click with AZURA®...
Geräte an AZURA® Click anbringen 3.1.2 Gerät abnehmen Ablauf 1. Den Griff des Tragschienenhalters nach unten ziehen 2. Das Gerät schräg nach oben abnehmen Abb. 8 Abnehmen des Geräts am Beispiel der Interface Box AZURA® Click Beiblatt, V6711...
Geräte an AZURA® Click anbringen 3.2 Air Sensor 3.2.1 Air Sensor anbringen Voraussetzung: Die Metallschiene ist entfernt (Abb. 9). AZURA® Click ist befestigt. Ablauf 1. Die Metallschiene gegen den Federmechanismus nach hinten ziehen. 2. Metallschiene von Air Sensor abnehmen. Abb.
5. Die untere Kante des Air Sensors an die untere Kante der Tragschiene drücken bis Air Sensor einrastet. Abb. 10 Position des Air Sensors Video: Auf dem KNAUER YouTube-Kanal finden Sie ein kurzes Tutorial, wie Sie den Air Sensor an AZURA® Click anbringen und abnehmen: AZURA® Click with air sensor.