Assembly And Adjustments - DeWalt D23550 Originalanweisungen

If the supply cord is damaged, it must be replaced
by a specially prepared cord available through the
D WALT service organisation.
E
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in
the plug.
• Connect the blue lead to the neutral terminal.
WARNING: No connection is to be
made to the earth terminal.
Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 13 A.
Using an Extension Cable
An extension cord should not be used unless
absolutely necessary. Use an approved extension
cable suitable for the power input of your charger
(see technical data). The minimum conductor size is
1 mm 2 ; the maximum length is 30 m.
When using a cable reel, always unwind the cable
completely.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-
ups or when making repairs. Be sure
the trigger switch is in the OFF position.
An accidental start-up can cause injury.
Depth of Cut Adjustment (fi g. 1–3)
1. Loosen the depth adjustment knob (n).
2. Move the shoe (f) to obtain the correct depth of
cut.
3. Tighten the depth adjustment knob (n).
WARNING: For optimal results, allow
the saw blade to protrude from the
workpiece by about 3 mm (see inset in
figure 3).
Bevel Adjustment (fi g. 4)
The bevel angle can be adjusted between 0° and
45° for the D23550 and between 0° and 55° for the
D23650.
1. Loosen the bevel adjustment knob (k).
2. Set the bevel angle by tilting the saw shoe (f)
until the mark indicates the desired angle on the
scale.
3. Tighten the bevel adjustment knob (k).
Shoe Adjustment for 90° Cuts
(fi g. 1, 5)
1. Adjust the saw to 0° bevel.
2. Retract the blade guard using the lever (h) and
place the saw on the blade side.
3. Loosen the bevel adjustment knob (k).
4. Place a square against the blade and shoe to
adjust the 90° setting.
5. Adjust the stop (o) as required.
Replacing the Saw Blade (fi g. 6)
1. Engage the blade lock button (d) and unscrew
the blade clamping screw (q) by turning
counterclockwise using the spanner (r) supplied
with the tool.
2. Retract the lower blade guard (i) using the
lever (h) and replace the blade (j). Reinstall the
washers (s, t) in the correct position.
3. Check the direction of rotation of the blade.
4. Thread on the blade clamping screw (q) by
hand to hold the washer in position. Turn
clockwise.
5. Press the blade lock button (d) while turning the
spindle until the blade stops rotating.
6. Tighten the blade clamping screw firmly using
the spanner.
Adjusting the Riving Knife (fi g. 6)
For the correct adjustment of the riving knife (g),
refer to the inset in figure 6. Adjust the clearance
of the riving knife after changing the saw blade or
whenever necessary.
1. Adjust the depth of cut to 0 mm to access the
clamping screws of the riving knife.
2. Loosen the screws (u) and pull out the riving
knife to its maximum length.
3. Adjust the clearance and tighten the screws
(torque: 4–5 Nm).
Mounting and Adjusting the Parallel
Fence (fi g. 7)
The parallel fence (o) is used for cutting parallel to
the edge of the workpiece.
EN G LI SH
33