Low Battery Warning - DeWalt XR LI-ION DCD992 Bersetzt Von Den Originalanweisungen

drill in a position which may cause anyone to stare
into the light. Serious eye injury could result.

CAUTION: When using the tool as a spotlight, be sure
it is secured on a stable surface where it will not cause a
tripping or falling hazard.

CAUTION: Remove all accessories from the chuck before
using the drill as a spotlight. Personal injury or property
damage could result.

Low Battery Warning

When in spotlight mode and the battery is nearing complete
discharge, the spotlight will flash twice and then dim. After two
minutes, the battery will be completely discharged and the
drill will immediately shut down. At this point, replace with a
fresh battery.

WARNING: To reduce the risk of injury, always have a
back-up battery or secondary lighting available if the
situation warrants it.
Keyless Single Sleeve Chuck (Fig. H–J)

WARNING: Do not attempt to tighten drill bits (or
any other accessory) by gripping the front part of the
chuck and turning the tool on. Damage to the chuck
and personal injury may result. Always lock off trigger
switch and remove the battery from the tool when
changing acces sories.

WARNING: Always ensure the bit is secure before starting
the tool. A loose bit may eject from tool causing possible
personal injury.
Your tool features a keyless chuck
one-handed operation of the chuck. To insert a drill bit or other
accessory, follow these steps.
1. Turn tool off and disconnect tool from power source.
2. Grasp the black sleeve of the chuck
use the other hand to secure the tool. Rotate the sleeve
anticlockwise (as viewed from the front) far enough to
accept the desired accessory.
3. Insert the accessory about 19 mm into the chuck and
tighten securely by rotating the chuck sleeve clockwise
with one hand while holding the tool with the other hand.
Continue to rotate the chuck sleeve until several ratchet
clicks are heard to ensure full gripping power.
TaBLE 1
Customizable Features
Worklight brightness
Worklight delay off
Maximum speed (RPM) Speed 1
in Drill Mode
Speed 2
Speed 3
Bind-Up Control®
6
with one rotating sleeve for
6
with one hand and
Home*
MED
20 secs
450
1300
2000
Enabled
*Factory presets are not customizable
in Home setting
nOTE: Be sure to tighten chuck with one hand on
the chuck sleeve and one hand holding the tool for
maximum tightness.
To release the accessory, repeat steps 1 and 2 above.
Mode Selector (Fig. A, D)
Your tool is equipped with a mode selector that allows 3
modes 17 to be customized using the Tool Connect™ app.
Home settings are active when the home indicator
Refer to Table 1 for customizable features.
Once configured, pressing the mode button
the tool will cycle through the modes
If you are unsure of the current configuration, press the mode
14
selector button to set the tool to the Home setting (home
16
indicator is lit).
D WALT Tool Connect™
e

WARNING: To reduce the risk of injury, remove
accessories from the tool chuck before any Tool
Connect™ interaction.

WARNING: When bind-up control is disabled and the
torque adjustment collar is in the drill or hammerdrill
position, the drill will not clutch. The drill may stall if
overloaded, causing a sudden twist.
NOTICE: Always check the tool configuration prior to
use. If you are unsure of the current configuration, press
the mode selector button
Home setting as described on the label and this manual.
This tool is capable of connecting with mobile devices that
support Bluetooth® Smart (or Bluetooth® 4.0) technology.
(To see if your mobile device is compatible, visit: http://www.
bluetooth.com/Pages/Bluetooth-Smart-Devices-List.aspx)
D WALT Tool Connect™ is an application for your smart device
e
(such as a smart phone or tablet) that connects the device to
your tool to allow you to configure specific tool functions. Refer
to Table 1 for factory presets.
nOTE: The Bluetooth® word mark and logos are registered
trademarks owned by the Bluetooth®, SIG, Inc. and any use of
such marks by D WALT is under license. Other trademarks and
e
trade names are those of their respective owners.
Factory Presets
Mode 1 Mode 2
OFF MED
20 secs 20 secs
450 450
1300 1300
2000 2000
Enabled Enabled
EnGLIsH
16
is lit.
14
on the foot of
17 .
14
(Fig. D) to set the tool to the
Customizable
Mode 3 Range
HIGH OFF-HIGH
20 minutes 0–20 minutes
450 140–450
1300 400–1300
2000 600–2000
Disabled/
Enabled
Enabled
39