Inhaltsverzeichnis
Werbung
(
. 3)
,
(1).
:
,
( ).
.
:
!
.
•
,
.
.
.
•
.
•
.
•
.
.
•
.
(
)
.
•
.
•
•
.
•
.
•
.
•
5
.
60
•
,
.
,
•
•
.
.
(
. 1)
(8)
(4)
.
,
.
,
:
•
. 3).
(
1,6 mm.
•
150 mm
.
150 mm
.
"
").
(
)
,
,
,
•
Ensure the ventilation openings are clear of debris at
all times.
•
Ensure there are no people of animals within 5 met-
res of your trimming area.
•
Before using the trimmer, remove any stones, sticks,
.
toys or other foreign objects from the area.
• Take care not to injure yourself on the blade fitted for
trimming the filament line. After extending new cut-
ter line always return the trimmer to its normal ope-
.
rating position before switching on.
•
Never reach into the underside of the appliance with
the power still on. Remove the plug from the power
,
socket before attempting to remove or touch the
trimmer thread hubcap.
Extension (fig.1)
For a better work-position you can put the extension (8)
between the upper body (4) and the lower body (5).
How to extend the trimmer thread
•
When you need to extend the trimmer thread, simple
tap the centre of the hub cap on the ground.
(5)
How to fit new trimmer thread
When you need to replace or fit new trimmer thread,
remove the plug from the power socket and proceed as
follows:
•
Depress the release lugs on the sides of the hubcap
(see fig. 3). Pull the hubcap off of the prop shaft (don't
lose the spring!). Remove the trimmer thread car-
tridge from the hubcap and either replace it with a
new cartridge or wind on new 1.6mm thread.
•
Push 150 mm of thread from one end of the reel
through the hole in the hubcap and 150 mm of thread
from the other end through the second hole. Re-fit the
cartridge ensuring no thread is trapped. Refit the
spring and hubcap assembly to the prop shaft and
(
push it in until it clicks in position.
!).
Symptom
Machine fails to operate
.
Mains socket faulty
Extension cable damaged
(
Fuse faulty/blown
Machine functions intermittently
Machines internal wiring damaged
Machine labours
Machine is not cutting
Line can't be fed automatically
(
. 4).
Line inside the spool entangled
Ferm
Ferm
Using the cord grip
•
To help secure the plug to the power cord make a loop
in the power cord (extension) and attach it to the cord
grip as shown (see fig. 4). Once secure attach the cord
to the plug. This will prevent accidental 'pull-out'.
Trouble shooting
The following table gives checks and actions that you can
perform if your machine does not operate correctly. If
this donít identify/remedy the problem, contact your
service centre.
Warning ! Switch off and remove the plug from the
mains before investigating a fault.
ı
CE
DECLARATION OF CONFORMITY
We declare under our sole responsibility that this pro-
duct is in conformity with the following standards or
standardized documents
EN 60335-1, EN 60335-2-91, EN 55014-1, EN
55014-2,EN 61000-3-2, EN 61000-3-3
Pr EN iso 10518/2003
in accordance with the regulations.
98/37/EEC, 73/23/EEC, 89/336/EEC
from01-01-2004
ZWOLLE NL
W. Kamphof
Quality department
It is our policy to continuously improve our products and
we therefore reserve the right to change the product
specification without prior notice.
Ferm BV, Zwolle, The Netherlands
Possible cause
Remedy
Power turned off
Turn power on
Use another socket
Inspect cable, replace if damaged
Replace fuse
Extension cable damaged
Inspect cable, replace if damaged
Contact service centre
Grass too high
Cut in stages
Line too short/broken off
Feed the line manually/automatically
Spool empty
Replace the spool
Inspect the spool, rewind if necessary
( UK )
5
Werbung
Inhaltsverzeichnis
