Herunterladen Inhalt Inhalt Diese Seite drucken

Specific Safety Warnings - Ferm LTM1003 Gebrauchsanweisung

Inhaltsverzeichnis

Werbung

Always use safety glasses. We also recommend the
use of ear protectors.
Wear the right clothes - not loose fitting or jewellery
and ensure garments cannot come into contact with
moving parts.
Wear non-slip shoes. Do not wear sandals or open-
toed shoes.
Before using any power tool, check first for damaged
parts and if found do not use it before the part or
parts have been replaced with new ones.
Do not use power tools when you are tired or have
been drinking alcohol.
Do not force the appliance - let it work at the rate for
which it was intended.
Do not overreach while working - you may lose your
balance.
You must switch off your tool at the tool's on/off
switch after use.
Never use this appliance without the safety guard fit-
ted. It must always remain fitted.
We strongly recommend the use of an RCD (Resi-
dual Current Device) of not more than 30 mA at the
plug socket when using this appliance.
Only use spare parts and attachments supplied by
Ferm. Use of attachments other than those supplied
or recommended by Ferm will invalidate your guar-
antee and could be dangerous.
Only use this appliance for its intended purpose -
trimming grass and light bushes.
Do not allow the power cord to lay on or across
sharp objects that might pierce the outer insulation.
Carry out a visual inspection of the power cord
before use and if it is damaged, have it replaced by a
specialist service centre. Do not use the appliance if
the cord is damaged.
ABOVE ALL - BE CAREFUL!
Mains Plug Replacement
If you in any doubt whatsoever regarding removing the
old plug and reconnecting a new one, you should contact
a competent electrician to do it for you.
Disconnect the plug from the electric socket.
Cut off the old plug and dispose of it safely. Under no
circumstances should anyone be able to find and use a
plug with exposed wires.
Only fit an approved plug with the correctly rated
fuse.
Attach the cores (wires) to their respective termi-
nals.
BROWN - L (Live)
4
BLUE - N (Neutral)
Ensure the outer cable (sheath) is firmly clamped in place
to avoid strain on the wires at the terminals.
Connecting to the Power Supply
Your trimmer is supplied with a non-rewireable moul-
ded plug and cable, incorporating a fuse. Should the fuse
need to be replaced at any time it must be replaced with
an approved to BS1362 fuse the same rating as the one
you are replacing.
The fuse cover is detachable. Never use the plug with the
cover off.
WARNING!
This appliance is double insulated and MUST NOT BE
EARTHED. If you have to rewire at any time please con-
nect as follows:
Attach the blue cable (Neutral) to the terminal mar-
ked N or coloured black or blue.
Attach the brown cable (Live) to the terminal marked
L or coloured red or brown.
Using Extension cables
All electrical connections e.g. extension cable, must
be of an approved waterproof type for outdoor use
and marked accordingly. Extension cables must be
three-core, one of which is EARTH.
As a supply for this machine always use an extension
cable of at least 0.75 mm2.
Always fully unwind extension cables before use.
Assembly
Attach the two parts (4 and 5 fig 1) of the trimmer
together. Push fit fully.
Attaching the guard (See Fig. 3 )
Attach the safety guard to the base of the trimmer as
shown using the two screws (1) supplied.
Please note: before use, remove the plastic thread cutter
cap (A).
Always fully unwind extension cables before use.

SPECIFIC SAFETY WARNINGS

Attention: Danger!
The cutting elements continue to rotate after the
motor is switched off.
If the cord becomes damaged during use, disconnect
the cord from the power supply immediately. DO
NOT TOUCH THE CORD BEFORE DISCON-
NECTING THE SUPPLY. Do not use the appliance if
the appliance cord or the extension cord is damaged.
Keep extension cord away from cutting elements.
Never fit metal cutting elements to this appliance.
Inspect and maintain the trimmer regularly. Have the
trimmer repaired only by an authorized repairer.
Keep your hands and feet away from the cutting area
at all times. Keep your second (front) hand on the
auxiliary handle.
Always hold the trimmer at a safe distance from the
body.
Always use gloves.
Always wear protective goggles.
Only use the trimmer in daylight.
.
,
!
.
/
,
Ferm
Ferm
ı
CE
.
.
EN 50144-1, EN 60335-2-91, EN 55014-1, EN
55014-2,EN 61000-3-2, EN 61000-3-3
Pr EN iso 10518/2003
.
98/37/
, 73/23/
01-01-2004
ZWOLLE NL
W. Kamphof
Ferm BV, Zwolle,
/
( GR )
,
.
.
, 89/336/
,
,
.
,
/
,
61

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Fgt-220

Inhaltsverzeichnis