Mounting And Operation - HIKOKI SV 1813DA Bedienungsanleitung

English
CAUTION
○ If the battery is charged while it is heated because it has
been left for a long time in a location subject to direct
sunlight or because the battery has just been used,
the pilot lamp of the charger lights up green or lights
for 1 second, does not light for 0.5 seconds (off for
0.5 seconds). In such a case, fi rst let the battery cool,
then start charging.
○ When the pilot lamp fl ickers in red (at 0.2-seconds
intervals), check for and take out any foreign objects in
the charger's battery connector. If there are no foreign
objects, it is probable that the battery or charger is
malfunctioning. Take it to your authorized Service
Center.

MOUNTING AND OPERATION

Action
Removing and inserting the battery*
Charging
Installing the sanding paper*
Attaching the dust bag*
3
Switch operation
Adjustment of speed*
4
How to hold the random orbit sander
*4 Adjustment of speed
The sander is equipped with an electric control circuit that enables speed control. To adjust the speed, turn the dial
shown in Fig. 7. When the dial is set to "1", the sander operates at the minimum speed (7000 min
to "6", the sander operates at the maximum speed (11000 min
and working effi ciency.
Material
Paintwork:
Sanding
Repairs
(scratches, rust spots)
Stripping
Wood:
Softwood
Hardwood
Veneers
Metals:
Aluminium
Steel
Stainless steel
Note: Please use this table as a standard.
*5 How to move the random orbit sander
CAUTION
○ Immediately after use, always ensure that the switch is in
the OFF position and pull out the battery.
○ Since the sander may suck in dust and debris, be careful
not to place it where there is much dust and debris when
it is still spinning right after use.
○ Looking from above, the sanding pad rotates clockwise
during the loaded operation, but it may rotate
counterclockwise during the no-load operation.
○ Never run the tool without the sanding paper. You may
seriously damage the pad.
○ Using the tool with the pad edge contacting the
workpiece may damage the pad.
Figure Page
2 2
1
3 2
4 2
2
5 3
6 3
7 3
8 3
Rough grinding
180
120
40
60–80
60
240
80
60
120
How to move the random orbit
sander*
5
Installing the selecting accessories
Attaching the dust collector
Selecting accessories
*1 Removing and inserting the battery
CAUTION
Before installing or removing the battery, turn the switch
to the OFF position.
If the battery is inserted with the switch in the ON
position, the motor will operate unexpectedly.
*2 Installing the sanding paper
Since the attachment is a hook-and-loop type, the
sanding paper can be installed easily by just pressing it
onto the pad. Gently pinch and hold together two places
on the edges of the sanding paper so that two holes are
visible on the bottom. (Fig. 4-a)
Overlap the two holes of the sanding paper with two
holes of the pad, and attach the whole surface of the
sanding paper to the pad so that the remaining holes are
also aligned. (Fig. 4-b)
*3 Attaching the dust bag
If too much dust accumulates in the dust bag, the dust
collection power will be reduced.
Dispose of dust as soon as possible.
). Adjust the speed according to the material to be cut
-1
Grain
Fine grinding
400
240
80
240
180
320
240
240
240
NOTE
Movement of the sander may tend to become unsteady
after new sanding paper has been installed, because of
the new, coarse grain of the paper. This can be avoided
by slightly tilting the sander forward or backward during
sanding or polishing. Sander movement will become
steady as the sanding paper surface becomes properly
abraded.
10
9 3
10 4
11 4
― 178
). When the dial set
-1
Dial scale
3–6
2–4
2–4
3–6
3–5
2–4
2–4
3–6
3–6