Removing The Batteries - Kärcher B 95 RS Originalbetriebsanleitung

Connect the connection cable to the
free battery poles (+) and (-).
Push the battery insert towards the
front.
Lock in the battery insert lock.
Caution
The battery can be damaged by deep dis-
charges. Charge the battery before com-
missioning the machine.
Attach the transposition protection to
the charger.
If the charger is accidentally plugged into
the appliance instead of the battery, the
control of the appliance may become dam-
aged. Therefore, the appliance is supplied
with a transposition protection, which must
be affixed to the charge plug of the charger.
(Depending on the model, there will be a
plug with or without traction relief.)
1 Transposition protection
2 Cord grip
Remove both screws and nuts from the
plug.
Place the included transposition protec-
tion on the plug.
Screw in the transposition protection
using the included new fasteners.
Charging battery
Note
The device is equipped with a safety mech-
anism to prevent total discharge, i.e. when
the permissible minimum capacity is
reached, then the machine can only be
driven.
Drive the machine directly to the charg-
ing station; avoid any steep gradients in
the process.
Danger
Risk of electric shock. Observe supply net-
work and fuse protection - see "Charger".
Only use the charger in dry rooms with suf-
ficient ventilation!
Note
Average charging time is approx. 10 hours.
The recommended chargers (matching the
batteries used) are regulated electronically
and will automatically switch off the charg-
ing process.
Danger
Danger of explosion. Wet batteries can
only be charged with opened battery cover.
Unscrew the locking screw of the bat-
tery cover.
Tilt the battery cover backwards.
All manuals and user guides at all-guides.com
Remove battery plug and join it to the
charging cable.
Connect the charger to the mains and
turn it on.
After charging
Switch off the charger and remove the
plug from the socket.
Pull the battery cable from the charger
cable and connect it to the appliance
plug.
Tilt the battery cover towards the front
and tighten the locking screw.
Further, in case of maintenance-free bat-
teries (wet batteries):
Add distilled water one hour before the
charging process comes to an end; fol-
low the correct acid level. There are
corresponding indicators on the battery.
At the end of the charging process, all
cells must gas.
Warning
Danger of causticization!
– Adding water to the battery in its dis-
charged state can cause the acid to
leak.
– Use safety glasses while handling bat-
tery acid and follow the safety instruc-
tions to avoid personal injury or damage
to clothes.
– Should the acid spray on to the skin or
clothes, rinse immediately with lots of
water.
Caution
Risk of damage!
– Use only distilled or desalinated water
(EN 50272-T3) for filling the battery.
– Do not add any substances (so-called
performance improving agents), else
warranty claims will not be entertained.
Recommended batteries
Only suited for appliances with mainte-
nance-free batteries (gel).
Battery set
3 x 12V/105 A, mainte-
nance-free (Gel)
Recommended chargers
Only suited for appliances with mainte-
nance-free batteries (gel).
Charger
36V, for maintenance-
free batteries
Batteries and chargers are available in spe-
cialised stores.
Maximum battery dimensions
Length Width
406 mm 533 mm
If you use wet batteries in the Bp model,
then follow the following instructions:
– It is necessary to conform to the maxi-
mum battery dimensions.
EN
-
– The battery cover needs to be opened
while charging wet (maintenance-free)
batteries.
– While charging wet batteries, follow the
specifications of the battery manufac-
turer.
Unscrew the locking screw of the bat-
tery cover.
Tilt the battery cover backwards.
Push the lock of the battery insert to-
wards the left and tilt it downward.
Pull the battery insert towards the rear.
Clamp off the minus pole of the battery.
Clamp off the remaining cables from the
battery.
Remove the batteries.
Dispose of the used batteries according
to the local provisions.
While standing, the device is protected
against rolling off with the help of an electri-
cal immobilising brake. To push the de-
vice, you need to first unlock the
immobilising brake.
Press the unlocking lever downward to
unlock the immobilising brake.
Danger
Risk of accident if the device rolls off. Apply
the immobilising brake again immediately
after finishing pushing the machine by
pushing the unlocking lever upward.
Caution
Risk of damage. Never move the appliance
faster than 7 km/h.
Note
Take the foot off the aceelerator pedal,
press the emergency-stop button to imme-
diately deactivate all functions and turn the
key switch to the "0" position.
Order No. Loosen the screws and remove the
wooden cage.
6.654-141.0
Cut plastic packing belt and remove foil.
Loosen the fixing at the wheels.
Place the enclosed wooden board at
the back of the appliance on the pallet
as a ramp and attach with screws.
Order No.
6.654-229.0
Height
432 mm
Remove both blocks from behind the
rear wheels.
Open the battery cover and remove the
steering wheel.
Insert the steering wheel and straight-
align the front wheel.
4

Removing the batteries

Pushing the device
Unloading
17