Briggs & Stratton 210000 Bedienungsanleitung Seite 8

WARNING
Accidental engine spark can cause an electric shock or fire and could result in
entanglement, traumatic amputation or laceration.
Before you make adjustments or repairs:
• Disconnect the spark plug wire and keep it away from the spark plug.
• Disconnect the battery wire from the negative battery terminal (only engines with
electric start.)
• Use only the correct tools.
When you check for spark:
• Use an approved spark plug tester.
• Do not check for spark with the spark plug removed.
Emissions Control Service
For maintenance, replacement, or repair of emissions control devices and
systems, contact a qualified off-road engine repair establishment or service
technician. However, for "no charge" emissions control service, the work must be done
by a factory authorized dealer. Refer to the Emissions Control Statements.
Maintenance Schedule
First 5 Hours
•
1
Change engine oil .
Intervals of 8 Hours or Daily
• Check the engine oil level.
• Clean the area around the muffler and controls.
• Clean the air intake grille.
Intervals of 25 Hours or Annually
• 2
Clean the air filter .
•
2
Clean the pre-cleaner .
Intervals of 50 Hours or Annually
•
3
Change the engine oil .
•
Replace the oil filter (if installed)
• Service the exhaust system.
Intervals of 100 Hours or Annually
•
4
Change the engine oil .
•
Replace the oil filter (if installed)
Annually
• Replace the spark plug.
• Replace the air filter.
• Replace the pre-cleaner.
• Replace the fuel filter.
•
1
Service the cooling system .
•
5
Check the valve clearance .
1
Only engines without an oil filter.
2
Clean more frequently in dusty conditions or when many particles are in the air.
3
Engines without oil filter or with standard black oil filter. See Specifications section for
the part number.
4
Engines with high-efficiency yellow or orange oil filter. See Specifications section for
the part number.
5
Not required unless engine performance problems occur.
Electronic Fuel Management System
The Electronic Fuel Management System monitors engine temperature, engine speed,
and battery voltage to adjust the choke during engine start-up and warm-up. There
are no adjustments on the system. If start-up or operation problems occur, contact an
Authorized Briggs & Stratton Dealer.
NOTICE Make sure to obey and follow the steps that follow or the Electronic Fuel
Management System could be damaged.
• DO NOT start the engine if the battery cables are loose.
8
3
.
4
.
• Turn the key to the OFF position or remove the starter switch before you
disconnect, remove, and / or install the battery.
• DO NOT use a battery charger to start the engine.
• DO NOT disconnect the battery cables during engine operation.
• When you disconnect the battery cables, first connect the positive (+) cable, and
then connect the negative (-) cable to the battery.
• When you charge the battery, turn the ignition switch to the OFF position, and
disconnect the negative (-) battery cable from the battery.
• DO NOT spray water directly on the Electronic Control Unit.
Carburetor and Engine Speed
Do not make adjustments to the carburetor or engine speed. The carburetor was
set at the factory to operate satisfactorily in most conditions. Do not change the
governor spring, linkages, or other parts to adjust the engine speed. If adjustments
are necessary, contact a Briggs & Stratton Authorized Service Dealer for servicing.
NOTICE
The equipment manufacturer specifies the maximum speed for the engine as installed
on the equipment. Do not exceed this speed. If you are not sure what the equipment
maximum speed is, or what the engine speed is set to from the factory, contact a Briggs
& Stratton Authorized Service Dealer for assistance. For safe and correct operation
of the equipment, the engine speed should only be adjusted by a qualified service
technician.
Servicing the Spark Plug
Check the spark plug gap (A, Figure 9) with a wire gauge (B). If necessary, set the
spark plug gap. Install and tighten the spark plug to the correct torque. For gap and
torque specifications, refer to the Specifications section.
NOTE: In some areas, it is mandatory by local law that you use a resistor spark plug
to decrease ignition signals. If a resistor spark plug was installed by the equipment
manufacturer, use the same type for replacement.
Servicing the Exhaust System
WARNING
During operation, the engine and muffler become hot. If you touch a hot engine,
thermal burns can occur.
Combustible materials, such as leaves, grass and brush, can catch fire.
• Before you touch the engine or muffler, stop the engine and wait two (2)
minutes. Make sure that the engine and muffler are safe to touch.
• Remove debris from the muffler and engine.
It is a violation of California Public Resource Code, Section 4442, to use or operate the
engine on any forest-covered, brush-covered, or grass-covered land unless the exhaust
system is equipped with a spark arrester, as defined in section 4442, maintained in
effective working order. Other states or federal jurisdictions may have similar laws;
reference Federal Regulation 36 CFR Part 261.52. Contact the original equipment
manufacturer, retailer, or dealer to obtain a spark arrester designed for the exhaust
system installed on this engine.
Remove debris from the muffler and cylinder area. Inspect the muffler for cracks,
corrosion, or other damage. Remove the deflector or the spark arrester, if equipped, and
inspect for damage or carbon blockage. If damage is found, install the replacement parts
before you operate the equipment.
WARNING
Replacement parts must be of the same design and installed in the same position as the
original parts. Other parts could result in damage or an injury.
Change Engine Oil
WARNING
Fuel and its vapors are flammable and explosive. Fire or explosion could result in
burns or death.
During operation, the engine and muffler become hot. If you touch a hot engine,
thermal burns can occur.
• If you drain the oil from the top oil fill tube, the fuel tank must be empty. If it is not
empty, fuel leakage can occur and cause a fire or an explosion.
• Before you touch the engine or muffler, stop the engine and wait two (2)
minutes. Make sure that the engine and muffler are safe to touch.
Used oil is a hazardous waste product and must be discarded of correctly. Do not
discard with household waste. Contact your local authorities, service center, or dealer
for safe disposal or recycling facilities.
Remove Oil
BRIGGSandSTRATTON.COM