Installing Accessories - Kärcher Puzzi 10/1 Bedienungsanleitung

Spray / suction hose
32
Wastewater container, removable
33
Wastewater container carrying handle
34
Cover seal
35
Fluff filter
36
Start-up
1. Check the power cord, extension cable and hoses
for damage before each start-up.

Installing accessories

1. Fit the suction pipe onto the floor nozzle and hand-
tighten the union nut on the floor nozzle.
2. If necessary, slide the handle onto the suction pipe
and hand-tighten in the desired position.
3. Fit the angle piece onto the suction pipe and hand-
tighten the union nut on the angle piece.
4. Connect the suction hose to the suction hose con-
nection on the device. Insert the spray hose cou-
pling into the spray hose connection on the device
and latch into place.
5. Connect the suction hose to the angle piece. Con-
nect the spray hose coupling to the angle piece and
latch into place.
Mixing the cleaning solution
DANGER
Danger from detergents
Risk of injury and damage
Observe all instructions that are included with the deter-
gents used.
Note
Warm water (maximum 50 °C) increases the cleaning
effect. Check the temperature resistance of the surface
to be cleaned.
Note
Use detergents sparingly to conserve the environment.
1. Mix fresh water and detergent in a clean container
(concentration as specified for the detergent). Dis-
solve the detergent in the water.
Filling the fresh water tank
1. Pour the cleaning solution into the fresh water tank.
The filling level must not exceed the "MAX" mark.
Defoaming agent
Note
Foam is generated in the wastewater container when
cleaning previously shampooed carpets. Foaming can
be prevented by adding defoaming agents.
1. Puzzi 10/1 only: Add defoaming agent (special ac-
cessory) to the wastewater container.
2. Puzzi 10/2 Adv only: Open the defoaming agent
container. Fill with defoaming agent (special acces-
sories).
Replacing the carpet adapter
1. Press the floor nozzle latch on one side.
2. Swing out and remove the carpet adapter.
3. Insert a new carpet adapter and engage the latch.
Working with accessories
Puzzi 10/2 Adv only:
Note
An additional power socket is provided for connecting
additional electrical devices.
DANGER
Danger of electric shock
Risk of injury and damage.
The socket is only intended for the direct connection of
the PW 30/1 additional brush washer head to the Puzzi
10/2 Adv. Any other use of the socket is prohibited.
Switching on the device
1. Connect the mains plug.
2. Press the suction switch to switch on the suction tur-
bine.
3. Press the spray switch to switch on the spray pump.
ATTENTION
Danger from cleaning solution
Risk of damage
Before using the device, check the object to be cleaned
for colour fastness and water resistance in an inconspic-
uous place.
1. Press the lever on the angle piece to spray the
cleaning solution.
2. Run over the surface to be cleaned in overlapping
paths. Pull the nozzle backwards (do not push).
3. When work is interrupted, the floor nozzle can
placed in the device carrying handle.
Switching off the device
1. Switch off the spray switch and the suction switch.
2. Pull out the mains plug.
Empty the wastewater container
1. Switch off the suction switch and the spray switch
when the wastewater container is full.
2. Remove the cover.
3. Remove the wastewater container from the device
and empty it.
Emptying the fresh water tank
1. Switch off the device.
2. Briefly operate the lever on the angle piece to re-
lieve pressure.
3. Disconnect the angle piece from the spray / suction
hose.
4. Hang the suction hose in the fresh water tank.
5. Press the suction switch to switch on the suction tur-
bine.
6. Suck the fresh water tank empty and switch off the
device.
7. Remove the cover.
8. Remove the wastewater container from the device
and empty it.
English
Operation
Cleaning mode
11