Makita bhr200 Betriebsanleitung Seite 6

NOTE:
• The battery charger is for charging Makita-battery cartridge. Never use it for other purposes or for other manufacturer's
batteries.
• When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time, it may not
accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the battery cartridge fully
after discharging it completely and recharging a couple of times.
• If you charge a battery cartridge from a just-operated tool or battery cartridge which has been left in a location exposed to direct
sunlight for a long time, the charging light may flash in red color. If this occurs, wait for a while. Charging will begin after the
battery cartridge is cooled by the cooling fan installed in the charger. When the temperature on battery is more than approx.
70°C, two charging lights may flash in red color, and when approx. 50°C – 70°C, one charging light in red color.
• If the charging light flashes alternately in green and red color, charging is not possible. The terminals on the charger or battery
cartridge are clogged with dust or the battery cartridge is worn out or damaged.
• Any of the following conditions indicates damage to the charger and/or battery cartridge. Ask your Makita Authorized or Factory
Service Center to check them.
1) The charging light does not flash (green) when the battery charger is plugged into a power source.
2) The charging light does not light up or flash (red) when the battery is inserted in the charger port.
3) Charging is not completed at even more than two hours after red light comes ON at start of charging.
Battery Type
B2417
B2430
Switch action (Fig. 3)
CAUTION:
Before inserting the battery cartridge into the tool, always
check to see that the switch trigger actuates properly and
returns to the ''OFF'' position when released.
To start the tool, simply pull the trigger. Tool speed is
increased by increasing pressure on the trigger. Release the
trigger to stop.
Reversing switch action (Fig. 4)
CAUTION:
• Always check the direction of rotation before operation.
• Use the reversing switch only after the tool comes to a
complete stop. Changing the direction of rotation before the
tool stops may damage the tool.
• When not operating the tool, always set the reversing switch
lever to the neutral position.
This tool has a reversing switch to change the direction of
rotation. Depress the reversing switch lever from the A side for
clockwise rotation or from the B side for counterclockwise
rotation. When the switch lever is in the neutral position, the
switch trigger cannot be pulled.
Selecting action mode
Rotation with hammering (Fig. 5)
For drilling in concrete, masonry, etc., depress the lock button
and rotate the change lever so that the pointer points to the
symbol. Use a tungsten- carbide tipped bit.
Rotation only (Fig. 6)
For drilling in wood, metal or plastic materials, depress the
lock button and rotate the change lever so that the pointer
points to the symbol. Use a twist drill bit or wood bit.
Hammering only (Fig. 7)
For chipping, scaling or demolition operations, depress the
lock button and rotate the change lever so that the pointer
points to the symbol. Use a bull point, cold chisel, scaling
chisel, etc.
CAUTION:
• Do not rotate the change lever when the tool is running.
The tool will be damaged.
• To avoid rapid wear on the mode change mechanism, be
sure that the change lever is always positively located in
one of the three action mode positions.
6
Capacity (mAh)
1,700
3,000
Number of cells
20
20
Installing or removing bit
Important:
Always be sure that the tool is switched off and the battery
cartridge is removed before installing or removing the bit.
Clean the bit shank and apply the bit grease provided to it
before installing the bit. (Fig. 8)
Insert the bit into the tool. Turn the bit and push it in until it
engages. (Fig. 9)
If the bit cannot be pushed in, remove the bit. Pull the chuck
cover down a couple of times. Then insert the bit again. Turn
the bit and push it in until it engages. (Fig. 10)
After installing, always make sure that the bit is securely held
in place by trying to pull it out.
To remove the bit, pull the chuck cover down all the way and
pull the bit out. (Fig. 11)
Depth gauge (Fig. 12)
The depth gauge is convenient for drilling holes of uniform
depth. Loosen the clamp screw and adjust the depth gauge to
the desired depth. After adjusting, tighten the clamp screw
firmly.
NOTE:
The depth gauge cannot be used at the position where the
depth gauge strikes against the gear housing/motor housing.
Side grip (Fig. 13)
CAUTION:
Always use the side grip to ensure operating safety when
drilling in concrete, masonry, etc.
The side grip swings around to either side, allowing easy
handling of the tool in any position. Loosen the side grip by
turning it counterclockwise, swing it to the desired position and
then tighten it by turning clockwise.
Bit angle
(when chipping, scaling or demolishing)
Important:
Always be sure that the tool is switched off and the battery
cartridge is removed before changing the bit angle.
To change the bit angle, depress the lock button and rotate the
change lever so that the pointer points to the V symbol. Turn
the bit to the desired angle. (Fig. 14)
Depress the lock button and rotate the change lever so that
the pointer points to the
Then make sure that the bit is securely held in place by turning
it slightly.
Charging time
Approx. 30 min.
Approx. 60 min.
symbol. (Fig. 15)