Inhaltsverzeichnis
Werbung
Ferm
.
.
,
.
.
,
,
.
,
,
,
.
.
o
Ferm.
.
,
.
.
NiCd
.
Ferm
.
,
.
.
54
ı
CE
,
.
prEN50260-1, prEN50260-2-1, prEN50260-2-2,
EN55014-1, EN55014-2,
EN60335-1,EN60335-2-29,
EN61000-3-2, EN61000-3-3.
:
98/37/EEC
73/23/EEC
89/336/EEC
01-09-2000-
GENEMUIDEN NL
W. Kamphof
.
Quality department
,
,
.
( GR )
UK
English
Cordless impact drill
:
THE NUMBERS IN THE FOLLOWING TEXT
CORRESPOND WITH THE PICTURES AT PAGE 2.
TECHNICAL SPECIFICATIONS
Voltage
Voltage battery charger
Frequency battery charger
Capacity battery
Charging time
Speed, no load
Impact frequency
Machine weight (incl. 1 battery) | 2.5 kg
L pa Sound pressure level
L wa Sound power level
Vibration
PACKAGE CONTENTS
1 Cordless drill
2 Batteries
1 Battery charger
15 Accessories
1 Blow case
1 Instruction manual
1 Guarantee card
Check the machine and accessories for transport
damage.
PRODUCTINFORMATION
Fig. A
1 Direction switch
2 On/off switch
3 Torque setting ring
4 Impact sleeve
5 Chuck
6 Battery
SAFETY INSTRUCTIONS
The following symbols are used in these instructions for
use:
Denotes risk of personal injury, loss of life or
damage to the tool in case of non-observance of
the instructions in this manual.
Denotes risk of electric shock.
Carefully read this manual before using the machine.
Make sure that you know how the machine functions and
how to operate it. Maintain the machine in accordance
with the instructions to make sure it functions properly.
Ferm
Ferm
Keep this manual and the enclosed documentation with
the machine.
Electrical safety
Warning! When using electric tools, basic safety
precautions should always be followed to reduce the
risk of fire, electric shock and personal injury. Read
all these instructions before attempting to operate
this product and save these instructions.
Always check that the voltage on the batterypack
corresponds to the voltage on the rating plate. Also
check that your mains voltage corresponds to the input
| 24 V — ---
voltage of the battery charger.
| 230 V~
| 50 Hz
The machine is double insulated in accordance
| 1.2 Ah (NiCd)
with EN60335; therefore no earth wire is
| 1 h
required.
| 0-900/min
| 0 -16200/min
Replacing cables or plugs
Immediately throw away old cables or plugs when they
| 91.3 dB(A)
have been replaced by new ones. It is dangerous to insert
| 104.3 dB(A)
the plug of a loose cable in the wall outlet.
| 7 m/s
2
Using extension cables
Only use an approved extension cable suitable for the
power input of the machine. The minimum conductor
size is 1.5 mm
2
. When using a cable reel always unwind
the reel completely.
SPECIAL SAFETY INSTRUCTIONS
IMPORTANT SAFETY ADVICE
CONCERNING THE BATTERY PACK &
BATTERY CHARGER
If you should come into contact with any acid
from the Battery pack, wash the affected parts
with water immediately. If acid should come into
contact with the eyes, rinse them immediately
with water and seek medical advice as soon as
possible.
1. Before using both the battery pack and the battery
charger, make sure you have read and understood
the operating instructions and safety information.
2. Only use the battery pack with the battery charger
provided – using other chargers could be dangerous.
3. Keep the battery pack, tool and battery charger away
from damp and wet conditions.
4. Before using the battery charger, check all wires are
properly connected.
5. If any wires on the charger are damaged, do not use it
until these have been replaced.
6. When the charger is not in use it should not be
plugged in. When unplugging, do not pull the plug out
by the cable.
7. If the charger breaks down or suffers from other
technical problems, take it to a recognised dealership
to be checked before using it again. Any damaged
parts must be replaced.
8. Take care when handling the battery pack, do not
drop it or knock it against other things.
9. Never attempt to repair the battery charger or
battery pack yourself; this can be extremely
dangerous. Repairs should always be carried out by a
3
Werbung
Inhaltsverzeichnis
