Heating The Sauna Room; Using The Sauna Climate Device; Adjusting The Temperature; Regulation Of The Sauna Climate - Saunum Primary Set Bedienungs- Und Installationsanleitung

HEATING
THE SAUNA ROOM
Before using the sauna climate device for
the first time, make sure that:
• the electrical connections meet the
requirements;
• the supply voltage corresponds to
the nominal ratings allowed for the
sauna climate device;
• the protective earth (PE) is in work-
ing order;
• the attachments of the sauna cli-
mate device housing are in order;
• the sauna climate device is pro perly
attached to the wall;
• the over-current fuses are in working
order;
• the fan rotor rotates smoothly;
• there are no tools or materials left
after mounting the device in the
housing.
When switching the sauna climate device
on, check:
• the direction of the air flow – the air
intake from the upper and the out-
put from the lower opening;
• that there is no vibration or excessive
noise when the fan is running.
When the sauna climate device is switched
on for the first time, the heaters and the
stones will emit an odour. The sauna room
must be properly ventilated to remove the
odour.
12
If the power of the heater is suitable for the
sauna room, it takes 45-90 minutes to reach
the desired temperature in a properly insu-
lated sauna room. The stones are usually
heated to the steam temperature at the
same time as the sauna room. Only switch
the device fan on just before entering the
sauna room – this will help to prevent the
sauna bench from overheating and an
excessive energy consumption. Saunum's
recommended temperature for sauna
operation is 65 ° to 80 °C.
USING THE SAUNA
CLIMATE DEVICE
NB! Before switching the sauna climate
device on, always make sure that nothing is
above or near it.
The operating time of the sauna climate
device model Sauna Primary Set may be
adjusted by a separate control device.
• Do not connect the device directly to
the mains!
• The sauna climate device must not
be used if the components of its
housing have been removed and/
or the wiring diagram has been
changed.
• Children should not be allowed to
access or play with the sauna climate
device.
• When switching the sauna cli-
mate device on and off, refer to the
instructions for use of the control
device you are using.
NB! After using the sauna, make sure that
all parts of the sauna climate device are
switched off (the heating and the fan have
stopped).
ADJUSTING
THE TEMPERATURE
NB! It is recommended to keep the air cir-
culation fan of the sauna climate device
switched off during the heating of the
sauna room!
In this case, the sauna room heats up faster
and the sauna bench does not get too hot
during the heating. To find the right setting,
start testing at the lowest temperature and
lowest airflow rate. If the temperature be-
comes too high while in the sauna room,
reduce the maximum temperature in the
sauna room or the fan speed of the sauna
climate device.
REGULATION OF THE
SAUNA CLIMATE
The amount of air circulation generated by
the device is regulated by a rotary switch
located on the front of the device, in the
middle of the lower part. The switch has four
positions and may be turned both clockwise
and anticlockwise. When the line on the
switch button points to the left, the fan of
the sauna climate device is switched off.
The airflow speed increases by turning the
switch clockwise, you may choose between
three different speeds. To regulate the air
temperature in the sauna room, there is a
steam air cooling damper on the left side of
the heater housing, lower than the device
stone area (see page 25). The recommen-
ded setting is to keep the cooling damper
1/3 open. To cool the steam, try to open the
damper little by little.
USE OF HIMALAYAN
SALT BALLS
The sauna climate device comes with Hima-
layan salt balls. The use of salt balls in the
device is optional and does not affect the
main function of the device.
To use the salt balls, they must be installed
in the sockets between the air outlet grille
and the fan. Make sure that the salt balls
are installed correctly and do not impede
the fan rotation.
To install or remove the salt balls, remove
the front panel (see page 29) and place the
salt balls in their sockets. After installing or
removing the salt balls, reposition the front
panel. The sauna climate device may only
be used with the front panel in place!
Do not use/start the device if the salt balls
get into the fan housing!
NB! The use of third-party salt balls is not
covered by the device warranty.
13