Inhaltsverzeichnis
Werbung
DK
• Sørg for at knappen til omløbsretningen (5
på fig. A) står i den midterste position, for at
undgå utilsigtet start af maskinen.
• Sæt batteriet (5) ind i maskinens sokkel
som vist på tegningen. Tryk det helt i bund
så det går i hak.
• For at fjerne batteriet skal du trykke
låsekapperne (10) på begge sider ind og
trække batteriet ud af maskinens sokkel.
4. BETJENING
Overhold altid sikkerhedshenvisning
erne, og følg de relevante forskrifter.
Hold maskinen ordentligt fast, og tryk boret
ensartet ind i emnet. Undgå at overbelaste
maskinen. Anvend udelukkende bor som ikke
udviser synligt slid. Slidte bor har en negativ
indflydelse på maskinens funktionsevne.
Indstilling af drejningsmoment
Fig. D
Maskinen har 16 forskellige indstillinger for
drejningsmoment til regulering af den kraft
hvormed skruer bliver skruet i eller ud.
• Sæt indstillingsringen for drejningsmoment
(3) i den ønskede position.
De indstillinger af drejningsmomentet der
er til rådighed, vises på indstillingsringen
dels med cifrene fra 1 til 8, dels med prikker
mellem cifrene som angiver
mellempositioner (dvs. i alt 16).
• Man skal helst vælge den laveste position
der giver tilstrækkelig kraft til at dreje
skruen rundt. Vælg en højere position hvis
motoren "glider i koblingen".
Anvendelse som skruetrækker.
• Sæt knappen for omløbsretningen (6) i
position 'R' for at skrue skruer i.
• Sæt knappen for omløbsretningen (6) i
position 'L' for at skrue skruer ud.
Boring
• Drej indstillingsringen for drejningsmoment
(3) i boreposition.
54
Sørg for at knappen for
omløbsretningen (6) altid står i
position 'R' når du borer.
Start og stop
Fig. A
• Tryk på startknappen (1). Du kan regulere
maskinens omdrejningstal ved at trykke
mere eller mindre hårdt på knappen.
• Når du slipper startknappen (1), bliver
patronen straks bremset, og der er ikke
noget efterløb.
• Når maskinen er slukket, kan du blokere
den ved at sætte knappen for omløbs-
retningen (6) i den midterste position.
Læg først maskinen fra dig når
motoren står helt stille. Læg ikke
maskinen på et støvet underlag. Der
kan trænge støv ind i mekanismen.
Opladning af batterier
Det vedlagte batteri er ikke opladet ved
leveringen.
• Brug kun batteriopladeren ved
temperaturer mellem +5º og + 40º Celsius.
• Brug kun batteriopladeren i tørre, udluftede
lokaler.
Opladning
Fig. E
• Sæt batteriholderen på et plant bord og
sæt batteriet i batteriholderen. Vær op-
mærksom på markeringerne af + og – pol.
• Sæt netadapterens adapterstik i stikket på
siden af batteriholderen.
• Sæt netadapteren i stikkontakten.
• Den røde opladningslampe på
batteriholderen lyser for at vise, at batteriet
er ved at blive opladet.
• Opladningen af et helt afladet batteri tager
cirka 5 timer første gang og derefter cirka 3
timer.
Det røde lys slukkes ikke auto-
matisk, når opladningstiden er forbi!
Tag batteriet ud af opladeren inden 5
timer. Hvis batteriet ikke tages ud af
opladeren efter opladningstiden, kan
det blive overophedet.
Ferm
• Move the direction reversing switch (6) to
the centre in order to lock the appliance in
its disabled state.
Only lay down the appliance when it has
stopped running completely. Do not place it on
a dusty surface as particles of dust could get
into the mechanism.
Charging the battery
The included battery is delivered in non-
charged condition.
• Only use the battery charger in a
temperature range between +5° to + 40º
Celsius.
• Only use the battery charger in dry,
ventilated rooms.
Charging
Fig. E
• Place the battery holder on a flat table and
put the battery in the battery holder. Pay
attention to + and - pole markings.
• Put the adapter plug of the net adapter in
the connector on the side of the battery
holder.
• Put the net adapter in the socket.
• The red charging lamp on the battery
holder will illuminate indicating the battery
is being charged.
• The charging process of a fully discharged
battery will take approximately 5 hours the
first time and afterwards approximately 3
hours.
After the charging time the red light
will not switch off automatically!
Remove the battery within 5 hours
from the charger. If the battery is not
removed from the charger after the
charging period it may become
overheated.
Discharging the battery
Not only charging batteries is
important, discharging is of equal
importance or even greater
importance.
Ferm
• When the battery is charged the cordless
drill has to be used until you start noticing
that the power of the drill is diminishing and
that the maximum rotational speed is not
reached.
• The battery is almost discharged now. Only
now you can start charging the battery.
• Charging the battery while it is still charged
for say one-third of capacity, the so-called
'memory effect' can occur. Since during
charging only the discharged part of the
battery capacity of the battery is being
charged now, the battery can start
crystallizing in the one-third that is still
charged. This part of the battery capacity
can never be used afterwards.
• Do not discharge the battery to the
minimum. As soon as you notice that the
power or the maximum rotational speed is
diminishing, you have to charge the
battery. When you proceed using the drill
and the battery becomes fully discharged,
the so-called 'switch of poles effect' can
occur. The polarity of the battery poles will
be switched: the '+'will become '-' and the '-
' will become the '+'. Once this has
occurred the polarity will remain switched
during loading and this will damage the
battery irreparable.
When the cordless drill is not being
used over a longer period of time,
the battery has to be charged fully
first. The battery has to be stored in
charged condition.
5. SERVICE & MAINTENANCE
Make sure that the machine is not
live when carrying out maintenance
work on the motor.
The machines have been designed to operate
over a long period of time with a minimum of
maintenance. Continuous satisfactory
operation depends upon proper machine care
and regular cleaning.
GB
07
Werbung
Inhaltsverzeichnis
