Makita DUC122 Betriebsanleitung Seite 13

– The protective jacket consists of 22 layers of
nylon and protects the operator against cuts. It is
always to be worn when working from elevated
platforms (cherry pickers, lifts), from platforms
mounted on ladders or when climbing with ropes.
– The protective brace and bib overall is made of
a nylon fabric with 22 layers and protects against
cuts. We strongly recommend its use.
– Protective gloves made of thick leather are part
of the prescribed equipment and must always be
worn during operation of the chain saw.
– During operation of the chain saw safety shoes
or safety boots fitted with anti skid sole, steel toe
caps and protection for the leg must always to be
worn. Safety shoes equipped with a protective
layer provide protection against cuts and ensure
a secure footing. For working in trees the safety
boots must be suitable for climbing techniques.
Vibration
1. Individuals with poor circulation who are exposed to
excessive vibration may experience injury to blood
vessels or the nervous system. Vibration may cause
the following symptoms to occur in the fingers,
hands or wrists: "Falling asleep" (numbness), tin-
gling, pain, stabbing sensation, alteration of skin
colour or of the skin. If any of these symptoms
occur, see a physician! To reduce the risk of "white
finger disease", keep your hands warm during oper-
ation and well maintain the equipment and accesso-
ries.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this instruc-
tion manual may cause serious personal injury.
IMPORTANT SAFETY INSTRUCTIONS FOR
BATTERY CARTRIDGE
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using bat-
tery.
2. Do not disassemble or tamper with the battery
cartridge. It may result in a fire, excessive heat, or
explosion.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4. If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
5. Do not short the battery cartridge:
(1) Do not touch the terminals with any conduc-
tive material.
(2) Avoid storing battery cartridge in a container
with other metal objects such as nails, coins,
etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.
6. Do not store and use the tool and battery car-
tridge in locations where the temperature may
reach or exceed 50 °C (122 °F).
7. Do not incinerate the battery cartridge even if it
is severely damaged or is completely worn out.
The battery cartridge can explode in a fire.
8. Do not nail, cut, crush, throw, drop the battery
cartridge, or hit against a hard object to the bat-
tery cartridge. Such conduct may result in a fire,
excessive heat, or explosion.
9. Do not use a damaged battery.
10. The contained lithium-ion batteries are subject
to the Dangerous Goods Legislation require-
ments.
For commercial transports e.g. by third parties, for-
warding agents, special requirement on packaging
and labeling must be observed.
For preparation of the item being shipped, consult-
ing an expert for hazardous material is required.
Please also observe possibly more detailed national
regulations.
Tape or mask off open contacts and pack up the bat-
tery in such a manner that it cannot move around in
the packaging.
11. When disposing the battery cartridge, remove it
from the tool and dispose of it in a safe place.
Follow your local regulations relating to disposal
of battery.
12. Use the batteries only with the products speci-
fied by Makita. Installing the batteries to non-com-
pliant products may result in a fire, excessive heat,
explosion, or leak of electrolyte.
13. If the tool is not used for a long period of time,
the battery must be removed from the tool.
14. During and after use, the battery cartridge may
ENC007-17
take on heat which can cause burns or low tem-
perature burns. Pay attention to the handling of
hot battery cartridges.
15. Do not touch the terminal of the tool immediately
after use as it may get hot enough to cause
burns.
16. Do not allow chips, dust, or soil stuck into the
terminals, holes, and grooves of the battery car-
tridge. It may cause heating, catching fire, burst and
malfunction of the tool or battery cartridge, resulting
in burns or personal injury.
17. Unless the tool supports the use near high-volt-
age electrical power lines, do not use the battery
cartridge near high-voltage electrical power
lines. It may result in a malfunction or breakdown of
the tool or battery cartridge.
18. Keep the battery away from children.
SAVE THESE INSTRUCTIONS.
CAUTION:
Only use genuine Makita batteries. Use of non-genu-
ine Makita batteries, or batteries that have been altered,
may result in the battery bursting causing fires, personal
injury and damage. It will also void the Makita warranty
for the Makita tool and charger.
13