Milwaukee M18 FN15GA Originalbetriebsanleitung Seite 14

OPERATION
There are two ways for working with this nailer (see also picture
section):
Single Sequential Actuation:
Drive the fastener by pulling the trigger.
Contact (Bump) Actuation:
Hold the trigger and drive the fastener by pushing the nailer against
the workpiece.
Reload Indicator
To indicate that the magazine is almost empty of fasteners (about
4-5 left), the workpiece contact will not compress, preventing
operation under usual pressure. Install more fasteners to continue
working.
Setting the Depth of Drive (see picture section)
Know what is behind your workpiece. A fastener could travel
through the workpiece and out the other side, striking a bystander
and causing serious injury. Lower the depth of drive to prevent the
fastener from being pushed all the way through the workpiece.
Thermal Overload
If the tool overheats, it will stop working and the power button/
actuation indicators will fl ash. Once the tool cools down, the tool will
revert to the selected mode. Restart work as normal.
CLEARING A JAMMED FASTENER
Most jams are caused by a fastener or part of a fastener wedging
between the driver blade and the nail guide. Fastener strips with an
incorrect collation angle or the wrong fastener gauge may cause
continuous jamming.
To clear the jam:
1. Remove battery pack.
2. WARNING! Always point the tool away from yourself and others
when installing or removing fasteners. Failure to do so could
result in injury.
3. Remove fastener strip from magazine.
4. Remove the fastener using needle-nose pliers. If necessary,
remove magazine from tool.
5. Follow the steps under "Required Daily Testing" before restarting
the work.
REQUIRED DAILY TESTING
WARNING: To reduce the risk of injury to yourself and
others, test the tool before beginning work each day or if the
tool is dropped, received a sharp blow, been run over, etc.
Complete the following checklist IN ORDER. If the tool does
not work as it should, contact a MILWAUKEE service facility
immediately.
Always point tool away from yourself and others.
1. Remove battery pack.
WARNING! Always point the tool away from yourself and others
when installing fasteners. Failure to do so could result in injury.
2. Check all screws, bolts, nuts, and pins on the tool. Any loose
fasteners must be tightened.
3. Pull back the fastener pusher on the magazine (to override the
Reload Indicator) and press the workpiece contact against a
workpiece. It must move smoothly.
4. With the workpiece contact pressed against the workpiece, pull
the trigger. It must move smoothly.
5. Insert battery pack.
6. Select the Single Sequential Actuation Operation. Without
pulling the trigger, pull back the fastener pusher on the
magazine (to override the Reload Indicator) and press
the workpiece contact against a workpiece. The tool must
not operate. Holding the workpiece contact away from the
workpiece, pull back the fastener pusher on the magazine (to
override the Reload Indicator). Pull and hold the trigger for 5
seconds. The tool must not operate. Continue to pull and hold
the trigger and push the workpiece contact against a workpiece.
26
The tool must not operate. Without pulling the trigger, pull back
the fastener pusher on the magazine (to override the Reload
Indicator) and press the workpiece contact against a workpiece.
Pull the trigger. The tool must operate. Release the trigger. The
driver must move up.
7. Select the Contact Actuation Operation. Holding the workpiece
contact away from the workpiece, pull back the fastener pusher
on the magazine (to override the Reload Indicator) and pull the
trigger. The tool must not operate. Continue to pull and hold the
trigger and push the workpiece contact against a workpiece. The
tool must operate.
8. If all previous tests work properly, set the tool for your work.
Select the operation and load fastener strips.
9. Set the depth of drive according to the "Setting the Depth of
Drive" section and see picture section.
10. If all tests operate properly, the tool is ready for use. Repeat
these tests before use each day or if the tool is dropped,
received a sharp blow, been run over, jammed, etc.
MAINTENANCE
Danger! Contains gas under pressure. In order to avoid injury never
attempt to open and/or modify the product. Product must be repaired
and serviced by authorized Milwaukee service station only.
The ventilation slots of the machine must be kept clear at all times.
Use only Milwaukee accessories and Milwaukee spare parts. Should
components need to be replaced which have not been described,
please contact one of our Milwaukee service agents (see our list of
guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please
state the machine type printed as well as the six-digit No. on
the label and order the drawing at your local service agents or
directly at: Techtronic Industries GmbH, Max-Eyth-Straße 10,
71364 Winnenden, Germany..
SYMBOLS
Please read the instructions carefully before starting
the machine.
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any work on
the machine.
Always wear goggles when using the machine.
Wear ear protectors!
Wear a suitable dust protection mask.
Wear gloves!
Fastener type:
Diameter
Length min./max.
Keep hands away!
ENGLISH
Content under pressure. Do not open the tool. Serious
injury may occur. Return to an authorized service
center for all repairs.
Do not dispose electric tools, batteries/rechargeable
batteries together with household waste material.
Electric tools and batteries that have reached the end
of their life must be collected separately and returned
to an environmentally compatible recycling facility.
Check with your local authority or retailer for recycling
advice and collection point.
n No-load-speed
0
V Voltage
Direct Current
European Conformity Mark
UK Conformity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark
ENGLISH 27