Operation - Makita CL070D Bedienungsanleitung

ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
the battery cartridge is removed before carrying
out any work on the tool.
Disposing of Dust
CAUTION:
• Empty the cleaner before it becomes too full, or
the suction force weakens.
• Be sure to empty out the dust inside the cleaner
itself. Failure to do so may cause the filter to be
clogged or the motor to be damaged.
► Fig.3: 1. Capsule 2. Suction inlet
In order to drop dust sticking on the filter in the capsule,
tap the capsule 4 or 5 times with your hand.
► Fig.4: 1. Capsule 2. Suction inlet
Now point suction inlet downwards, turn capsule in
direction of arrow in diagram, and disconnect capsule
slowly and straight.
NOTE:
• Dust may spill out when capsule is opened, so
be sure to set a garbage bag beneath capsule.
► Fig.5: 1. Prefilter 2. Capsule
Remove accumulated dust from inside of capsule and
off of prefilter.
► Fig.6: 1. Prefilter 2. Securing lip
Twist prefilter in direction of arrow to unfasten securing
lip from cleaner unit and then pull off prefilter.
► Fig.7: 1. Filter 2. Prefilter
Clean out fine dust from prefilter. Next, remove filter,
and lightly tap to dislodge dust.
Reassembly
► Fig.8: 1. Filter
Put on filter until it is fully in position on the cleaner unit.
NOTE:
• Make sure filter is put on straight without being
peeled back. If filter is put on incorrectly as
shown in diagram, dust will get into motor hous-
ing, and cause motor failure.
► Fig.9: 1. Filter
Connect prefilter. At this time, make sure to twist prefil-
ter so that securing lip is firmly locked into cleaner unit.
► Fig.10: 1. Prefilter 2. Securing lip
► Fig.11
Connect capsule. Align projection on capsule with pro-
jection on handle and then firmly twist capsule in direc-
tion of arrow until it is secured.
► Fig.12
► Fig.13: 1. Capsule 2. Handle 3. Projection
NOTE:
• Always remove dust ahead of time, as suction
power will be reduced if there is too much dust
in cleaner.
• Always be sure to check that both filter and pre-
filter are loaded correctly prior to using cleaner.
If they are not loaded correctly, dust will get into
the motor housing, and cause motor failure.
If the following examples occur, filter and prefil-
ter are not loaded correctly. Reload them cor-
rectly to rectify problem.
Problem Examples
Example 1: Only prefilter has been loaded (no filter)
► Fig.14: 1. Prefilter
Example 2: Only filter has been loaded (no prefilter)
► Fig.15: 1. Filter
Example 3: Filter has been loaded in a peeled back
state
► Fig.16: 1. Filter
Example 4: Prefilter's securing lip is not firmly locked
into groove of cleaner housing
► Fig.17: 1. Groove of cleaner housing 2. Prefilter
3. Securing lip

OPERATION

CAUTION:
• To connect attachments, such as nozzle,
twist-insert attachment in direction of arrow to
ensure secure connection during use. To dis-
connect attachment, twist-extract also in direc-
tion of arrow.
If attachment is twisted in the opposite direction,
when being connected or disconnected, capsule
may become loose.
► Fig.18: 1. Capsule
CAUTION:
• Keep away end of your hair, scarf, shawl, etc.
from the exhaust vents. They may be entangled
in the motor and cause injury.
► Fig.19
Cleaning (Suction)
Nozzle
Attach the nozzle to clean off tables, desks, furniture,
etc. Nozzle slips on easily.
► Fig.20: 1. Nozzle
Nozzle + Extension wand (Straight pipe)
The extension wand fits in between the nozzle and the
cleaner itself. This arrangement is convenient for clean-
ing a floor while standing erect.
► Fig.21: 1. Cleaner body 2. Extension wand
3. Nozzle
10 ENGLISH