Operation - Makita DVC260 Betriebsanleitung

Assembling hose/wand/nozzle
Connect the vacuum cleaner body with the hose,
wand and nozzle. Insert the hose cuff into the vacuum
cleaner body and turn it clockwise. Connect the nozzle
to the extension wand. After that, shoulder the vacuum
cleaner body then connect the hose with the extension
wand.
Connecting vacuum cleaner body and hose
► Fig.13: 1. Hose cuff 2. Vacuum cleaner body
Connecting extension wand and nozzle
► Fig.14: 1. Extension wand 2. Free nozzle
3. T-shape nozzle
NOTE: The free nozzle can be attached directly to
the hose.
Connecting hose and extension wand
► Fig.15: 1. Hose 2. Extension wand 3. Free nozzle
NOTE: The free nozzle can be attached to the hose
directly.
Installing filter bag
CAUTION:
Do not use a damaged filter bag.
Always use the vacuum cleaner with the filter bag
properly installed. Otherwise the vacuumed dust
or particles may be exhausted from the cleaner
and they may cause respiratory disease to the
operator.
NOTICE:
When the filter bag is already full, replace
with new one. Continuous use with the filter bag full
results in reduced suction power.
1. Unlock the latch by lifting the bottom side. Push
the grooved area to lift the front latching side. Pull the
latch to open the lid.
► Fig.16: 1. Hook 2. Lid
2.
Insert the filter bag into the slit on the upper side of
the room as illustrated.
► Fig.17: 1. Slit 2. Filter bag / Dust bag
When using the dust bag (optional accessory), insert
the brim of the dust bag into the slit.
► Fig.18: 1. Slit 2. Brim
3. Align the hole of the filter bag with the hose cuff
and push the cardboard portion to the end. Make sure
that the rubber ring on the filter bag goes over the rim
on the hose cuff.
► Fig.19: 1. Rubber ring on the filter bag 2. Rim on
the hose cuff 3. Cardboard portion of the
filter bag 4. Hose cuff

OPERATION

WARNING:
instructed on the use of the vacuum cleaner.
WARNING:
able for picking up hazardous dust.
CAUTION:
This cleaner is for dry use only.
CAUTION:
This cleaner is for indoor use only.
CAUTION:
Always insert the battery cartridge
all the way until it locks in place. If you can see the
red indicator on the upper side of the button, it is not
locked completely. Insert it fully until the red indicator
cannot be seen. If not, it may accidentally fall out of
the tool, causing injury to you or someone around
you.
1. Shoulder the vacuum cleaner body and fas-
ten upper and lower belts. Adjust the tightness as
necessary.
► Fig.20
2. Press button to start cleaning. If you want to
lower the suction power, press
time. Press button to stop.
► Fig.21
During cleaning, hook the switch box on the lower belt.
The hook can be slanted for lighting forward.
► Fig.22
When you suspend the operation, the hook on the hose
can be used for hanging the wand on the lower belt.
► Fig.23
NOTE: The vacuum cleaner will automatically
switches off and the LED light flashes when the vac-
uum cleaner is overheated due to the reduced air-
flow into the machine caused by clogged hose, pipe,
filter or other reasons. In this case, remove the cause
of the problem and cool the vacuum cleaner before
restarting.
3. Replace the filter bag when it becomes full. Open
the lid and take out the filter bag. Pull the strip on the
side of the opening to shut the filter bag and dispose of
the filter bag in whole.
► Fig.24: 1. Strip
When using a dust bag (optional accessory), take out
the dust bag and dispose of the dust by releasing the
latch.
► Fig.25: 1. Latch
NOTICE:
Periodically check the filter bag if it is
full. Continuous use with the filter bag full results in
reduced suction power.
NOTICE:
Do not use an used filter bag. The filter
bag is designed for single use. If you want to use the
bag repeatedly, use a dust bag (optional accessory).
10 ENGLISH
Operators shall be adequately
This vacuum cleaner is not suit-
button one more