Nylon Cutting Head - Makita UR006G Betriebsanleitung

1. Put the blade cover on the cutter blade.
2-tooth blade
► Fig.22
3-tooth blade
► Fig.23
4-tooth blade
► Fig.24
2.
Insert the hex wrench through the hole in the gear
case to lock the spindle. Rotate the spindle until the hex
wrench is fully inserted.
► Fig.25: 1. Nut 2. Cup 3. Clamp washer 4. Cutter
blade 5. Spindle 6. Receive washer 7. Hex
wrench
3.
Mount the cutter blade onto the receive washer
so that the arrows on the cutter blade and protector are
pointing in the same direction.
► Fig.26: 1. Arrow
4. Put the clamp washer and cup onto the cutter
blade and then tighten the nut securely by the box
wrench.
► Fig.27: 1. Box wrench 2. Hex wrench 3. Loosen
4. Tighten
NOTE: Tightening torque : 20 - 30 N•m
5.
Remove the hex wrench from the gear case.
To remove the cutter blade, follow the installation proce-
dures in reverse.

Nylon cutting head

NOTICE:
Be sure to use genuine Makita nylon
cutting head.
► Fig.28: 1. Nylon cutting head 2. Spindle 3. Hex
wrench 4. Loosen 5. Tighten
1. Insert the hex wrench through the hole in the gear
case to lock the spindle. Rotate the spindle until the hex
wrench is fully inserted.
2. Place the nylon cutting head onto the spindle and
tighten it securely by hand.
3. Remove the hex wrench from the gear case.
To remove the nylon cutting head, follow the installation
procedures in reverse.
Plastic blade
NOTICE:
Be sure to use genuine Makita plastic
blade.
► Fig.29: 1. Plastic blade 2. Spindle 3. Hex wrench
4. Loosen 5. Tighten
1. Insert the hex wrench through the hole in the gear
case to lock the spindle. Rotate the spindle until the hex
wrench is fully inserted.
2. Place the plastic blade onto the spindle and
tighten it securely by hand.
3.
Remove the hex wrench from the gear case.
To remove the plastic blade, follow the installation pro-
cedures in reverse.
OPERATION
Attaching the shoulder harness
WARNING:
control of the tool at all times. Do not allow the
tool to be deflected toward you or anyone in the
work vicinity. Failure to keep control of the tool
could result in serious injury to the bystander and the
operator.
CAUTION:
Always use the shoulder harness
attached to the tool. Before operation, adjust the
shoulder harness according to the user size to
prevent fatigue.
CAUTION:
Before operation, make sure that
the shoulder harness is properly attached to the
hanger on the tool.
CAUTION:
When you use the tool in combi-
nation of the backpack-type power supply such
as portable power pack, do not use the shoulder
harness included in the tool package, but use the
hanging band recommended by Makita.
If you put on the shoulder harness included in the
tool package and the shoulder harness of the back-
pack-type power supply at the same time, removing
the tool or backpack-type power supply is difficult in
case of an emergency, and it may cause an accident
or injury. For the recommended hanging band, ask
Makita Authorized Service Centers.
For UR006G
1. Put on the shoulder harness and fasten the
buckle.
► Fig.30
2. Clasp the hook on the shoulder harness to tool's
hanger.
► Fig.31: 1. Hook 2. Hanger
3. Adjust the shoulder harness to a comfortable
working position.
► Fig.32
The shoulder harness features a means of quick
release. Simply squeeze the sides of the buckle while
holding the tool to release the tool from the shoulder
harness.
► Fig.33: 1. Buckle
For UR007G
1. Clasp the hook on the shoulder harness to tool's
ring and hanger.
► Fig.34: 1. Ring 2. Hook 3. Hanger
2.
Put on the shoulder harness on your left shoulder.
Adjust the shoulder harness to a comfortable working
position.
► Fig.35
The shoulder harness features a means of quick
release. Simply squeeze the sides of the buckle while
holding the tool to release the tool from the shoulder
harness.
► Fig.36: 1. Buckle
23 ENGLISH
Be extremely careful to maintain