ABB HT846619 Bedienungsanleitung Seite 100

Demontage und Montage
5
Demontage
und Montage
Inhalt
1 Einleitung .................................................3
2 Gewichte ..................................................5
3 Turbolader abbauen und anbauen ...........9
4 Lager ausbauen und einbauen .............. 11
4.1 Verdichterseitiges Lager ausbauen ........ 11
4.2 Turbinenseitiges Lager ausbauen ..........19
4.3 Kontrolle und Beurteilen der Lager ........25
4.4 Turbinenseitiges Lager einbauen ...........29
4.5 Verdichterseitiges Lager einbauen .........37
4.6 Masse K, K1, K2, Spiele L und M ..........45
4.7 Messen des axialen Spiel Z ..................47
5 Rotor ausbauen und einbauen ...............49
5.1 Rotor ausbauen .....................................49
5.2 Turbinenschaufeln ersetzen ...................57
5.3 Verdichter wechseln ...............................57
5.4 Rotor einbauen ......................................59
6 Turbinendiffusor und Düsenring
ersetzen - VTR454 .................................61
6.1 Turbinendiffusor ersetzen ......................61
6.2 Düsenring ersetzen ................................63
7 Turbinendiffusor und Düsenring
ersetzen - VTR564 .................................65
7.1 Turbinendiffusor ersetzen ......................65
7.2 Düsenring ersetzen ................................71
8 Heben Luftaustrittsgehäuse ..................74
9 Heben Gasaustrittsgehäuse .................75
10 Heben Gaseintrittsgehäuse ...................76
11 Heben Fuss ............................................78
12 Reserveteile ...........................................80
13 Tabelle der Anziehmomente ...................83
ABB Turbo Systems Ltd
ABB Turbocharger VTR..4
Kap. / Chap. 5
5
Disassembly
and assembly
Contents
1 Introduction ..............................................3
2 Weights ....................................................5
3 Removing and installing
the turbocharger .......................................9
4 Removing and installing the bearings .... 11
4.1 Removing the compressor end bearing . 11
4.2 Removing the turbine end bearing .........19
4.3 Inspection and assessment of
the bearing .............................................25
4.4 Installing the turbine end bearing ...........29
4.5 Installing the compressor end bearing ...37
4.6 Distances K, K1, K2
Clearances L and M ...............................45
4.7 Measuring the axial clearance Z ...........47
5 Removing and installing the rotor ..........49
5.1 Removing the rotor.................................49
5.2 Replacing the turbine blades .................57
5.3 Replacing the compressor .....................57
5.4 Installing the rotor...................................59
6 Replacing the turbine diffuser and
nozzle ring - VTR454 .............................61
6.1 Replacing the turbine diffuser ................61
6.2 Replacing the nozzle ring .......................63
7 Replacing the turbine diffuser and
nozzle ring - VTR564 .............................65
7.1 Replacing the turbine diffuser ................65
7.2 Replacing the nozzle ring .......................71
8 Lifting air outlet casing ..........................74
9 Lifting gas outlet casing .........................75
10 Lifting gas inlet casing ............................76
11 Lifting foot...............................................78
12 Reserve parts .........................................80
13 Table of tightening torques .....................83
Volume: 83 pages
Edition: 08 / 2012
HZTL 10066
- F -
Seite / Page 1
Disassembly and assembly
ABB