Fitting Instructions - 3M PELTOR WS Protac XPI Bedienungsanleitung

COMPONENTS
(G:1) Headband (PVC, stainless steel)
(G:2) Two-point fasteners (POM)
(G:3) Ear cushion (PVC foil, PUR foam)
(G:4) Speech microphone
(G:5) On/Off/Mode button
(G:6) [+] button
(G:7) [–] button
(G:8) Bluetooth button
®
(G:9) External input PTT (*-111 models)
(G:10) External input jack, FLX 2

1. FITTING INSTRUCTIONS

1:1 Headband
(H:1) Slide out the cups and tilt the top of the cup out, as the
cable must be on the outside of the headband.
(H:2) Adjust the height of the cups by sliding them up or down
while holding the headband in place.
(H:3) The headband should be positioned across the top of the
head as shown and should support the weight of the headset.
1:2 Neckband
(J:1) Position the earcups over your ears so that the
cushions fully enclose the ears and seal tightly against the
head.
(J:2) Keep the cups in position, place the head strap on top
of your head and lock it tight in position.
(J:3) The head strap should be positioned across the top of
your head and should support the weight of the headset.
NOTE:The retention system of some helmets can interfere
with correct positioning of the earcups over the ears if the
neckband headset is donned before the helmet. If this
occurs with your helmet, you should don the helmet first and
the headset after securing the helmet onto your head.
1:3 Helmet attachment
(K:1) Insert the helmet attachment in the slot on the helmet
and snap it into place.
(K:2) Make sure that the cable is on the outside of the
headband.
(K:3) Work mode: Press the headband wires inwards until
you hear a click on both sides.
Make sure that the cups and the headband wires do not
press on the edge of the hard hat when in work mode as this
could reduce the noise attenuation of the earmuff.
(K:4) Ventilation mode: To switch the unit from work mode to
ventilation mode, pull outward on the ear cups until you hear
a click.
Avoid placing the cups against the helmet as this prevents
ventilation (K:5).
NOTE: Do not store the helmet with the helmet attachment in
ventilation mode. This causes stress on the helmet attachment.
NOTE: When the helmet is not in use, make sure that the
cups are left in work mode. This will decrease the stress on
the helmet attachment.
1:4 Microphone
(M:1) (M:2) To maximize the performance of the speech
microphone in noisy areas, position the microphone very
close to your mouth (less than 3 mm or 1/8 inch).
1:5 Replacing the helmet attachment plate
For proper fitting on different industrial safety helmets, the
helmet attachment plate may need to be replaced. Find the
recommended attachment in Table F. Other plates can be
obtained from your dealer. A screwdriver is needed to
replace the helmet attachment plate.
(N:1) Loosen the screw holding the plate and remove the
plate.
(N:2) Attach the appropriate plate while ensuring the left (L) and
right (R) designated plates are on the appropriate earmuff, if
applicable, and then tighten the screw.
2. OPERATING INSTRUCTIONS
2:1 Replacing the batteries (fig. 1)
1-2: Remove the battery compartment lid and insert the alkaline
batteries or ACK053.
3: The battery polarity must correspond to the marking in the
battery compartment. Low battery level is indicated by the
recurring voice message "low battery".
4-6: Hook the lid and close the compartment lid.
NOTE: Use only 3M™ PELTOR™ USB charger
FR09 and 3M™ PELTOR™ USB wall adapter FR08 with
3M™ PELTOR™ ACK053.
2:2 Operation time
Approximate operation time with new AA alkaline batteries and
fully charged ACK053 battery (1900 mAh):
• Level-dependent: approx. 150 hours
• Bluetooth and level-dependent: approx. 45 hours
®
NOTE:
Depending on the environment, temperature, and battery, the
operation time may vary.
2:3 Power on/power off (fig. 2)
Press and hold the On/Off/Mode button for approximately 2
seconds to switch the headset on or off. A voice message will
confirm that the unit has been switched on or off with the voice
message "power on" or "power off".
NOTE: The headset is automatically powered off after four hours
of inactivity. This is indicated by the voice message "automatic
power off".
2:4 Adjusting the sound source volume level (fig. 3)
To adjust the sound source volume level, short press (1 s) the [+]
or [–] button. Change the active sound source by short pressing
(1 s) the On/Off/Mode button.
The sound source can be:
• Ambient listening
• Streaming
• Phone
• Radio
4
EN