Gzxo; Peltor™ X Series Ear Muffs; Intended Use; Fitting Instructions - 3M Peltor X-Serie Bedienungsanleitung

GZXO

Products Include:
3M™ Peltor™ X Series Ear Muffs
Headband Version
X1A, X2A, X3A, X4A, X4A-OR and X5A
Neckband version:
X1B, X2B, X3B, X4B and X5B
Helmet Mounted Version
X1P5, X1P5-OR, X2P5, X3P5, X4P5, X4P5-OR, X5P5

INTENDED USE

These products are designed to help reduce exposure to hazardous
noise levels and loud sounds.
These products are available in headband, neckband and helmet
mounted versions.
The helmet mounted versions are tested and approved with
specified industrial safety helmets.
Refer to Table1 for further information on approved combination
Electrically Insulated.
The bracket arms of helmet attachment earmuffs are made of
non-conductive (sometimes referred to as 'dielectric') material whilst
the metal components of the attachment mechanisms are covered
in non-conductive material. The metal wire of the headband
earmuffs are covered in a non-conductive material. These products
were found to be electrically insulated, withstanding a voltage up to
1,2kV, at an external laboratory against a modified test method
based on EN 397:2012 under dry conditions. The user must
determine the overall suitability of this product for the intended
application taking into account any hazards other than noise for
which this product is tested and approved.
NOTE: The neckband version is NOT electrically insulated.
^ Warning
Always be sure that the complete product is:
- Suitable for the application;
- Fitted correctly;
- Worn during all periods of exposure;
- Replaced when necessary.
• This product may be adversely affected by certain chemical
substances.
• Further information should be sought from 3M.
• Leave the area immediately if the hearing protector becomes
damaged.
• The fitting of hygiene covers or sweat pads to the cushions may
affect the acoustic performance of the ear muffs.
• Do not modify or repair this product.
• Ear muffs, and in particular cushions, may deteriorate with use
and should be examined at frequent intervals for cracking and
leakage, for example.
• The acoustic seal may be adversely affected by wearing other
equipment, such as spectacles, respirators etc. This may
reduce attenuation. If in doubt, contact your safety officer or 3M.
• When worn, hearing protectors reduce ambient sounds which
may affect warning signals and vital communication. Always
ensure that you select the right product to match the working
environment so that vital communication and emergency
sounds remain audible.
• Ear muffs complying with EN352-1 and EN352-3 are of
' m edium size range' or ' s mall size range' or ' l arge size range' .
• ' M edium size range' helmet mounted ear muffs will fit majority of
wearers. ' S mall size range' or ' l arge size range' helmet
mounted ear muffs are designed to fit wearers for whom
' m edium size range' helmet mounted ear muffs are not suitable.
• Helmet mounted ear muffs must be used with the approved
helmet combination listed in Table1 only.
• Proper selection, training, use and appropriate maintenance are
essential in order for the product to help protect the wearer from
noise hazards. Particular attention should be given to
warning statements where indicated.
• Failure to follow all instructions on the use of these personal
protection products and/or failure to properly wear the complete
product during all periods of exposure may adversely affect the
wearer' s health, lead to severe or life threatening illness or
permanent disability.
See all instructions for use and save for continuing reference.

FITTING INSTRUCTIONS

Prior to fitting, inspect the product to ensure it is not damaged.
If this is discovered dispose of immediately and obtain a new pair.
Brush excess hair aside and remove any ear jewellery that may
affect acoustic seal before attempting to fit the hearing protector.
Headband Version
1. Pull the cups apart and place the ear muffs over the ears so that
the cushions form a snug seal around the ears (Figure 1).
2. Adjust the height for optimum comfort and fit by sliding the cups up
or down the guide whilst holding the headband in place (Figure 2).
3. Shows the product correctly fitted (Figure 3).
Neckband version:
X1B and X2B
4. Place the cups in position over the ears (Figure 4).
5. Keep the cups in position, place the head strap on top of your
head and lock it tight in position (Figure 5).
6. The head strap should be positioned across the top of your head
and should support the weight of the headset (Figure 6).
X3B, X4B and X5B
Step 1: Connect the two halves of the head strap together using the
hook and loop fastener (Figure 7).
Step 2: Insert the stitched end of the strap through the slots on each
of the ear cups (Figure 8). Each end of the strap should be held
securely in ear cup slot (Figure 9).
To adjust the length of the head strap pull the two halves apart and
re-attach so that the strap is firmly secured across the top of your
head (Figure 10).
Caution: The neckband earmuffs must be worn with the head strap
correctly attached to keep them firmly in position to maintain an
effective acoustic seal. The protection level provided by neckband
earmuffs may be reduced if the head straps are not worn correctly.
Helmet Mounted Version
Fitting the cup (Figure 11) Push the attachment blade firmly into the
slot on the side of the helmet until it clicks into place.
Working position (Figure 12) With the cups over the ears press the
8