Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Modell V-HB 13000:
Secure the handle (2) to the vibratory plate.
2 hexagon screws [M10x20mm], 2 washers [A 10.6] and 2
spring rings [Ø 10mm].
Secure the angle plate (5) with the star grip screw (4), on
the guide bar (2a)
Secure the throttle lever (3) with a hexagon screw M 5 x 25
and washer to the handle
Chassis
Slide the wheels (6) onto the axle (7) and secure them each
with a spring pin and washers.
Detach the spring pin and pull out the axle journal. Secure the
axes in the shown position using the spring pin.
Insert the bracket of the undercarriage (9) between the
retainer of the vibratory plate. Connect both by pushing the pin
(10) [Ø 14 x 100mm] through and securing it with a spring pin.
Slightly pull back the securing pin (8) if the pin cannot be
pushed through freely.
R
u
b
b
e
r
m
a
t
R
u
b
b
e
r
m
a
t
Place the vibratory plate on the rubber mat.
Secure the rubber mat (11) with the clamping plate (12) to the
base plate (A).
V-HB 8200:
2 hexagon screws [M10x25], 2 spring rings [Ø 10mm] and
2 washers [A 10].
V-HB 13000:
3 hexagon screws [M10x25], 3 spring rings [Ø 10mm] and
3 washers [A 10].
Use the rubber mat only when compacting paving stones,
concrete slabs or similar Other materials such as gravel,
crushed gravel, etc. must not be worked on with the rubber
mat.
Preparing for startup
The motor of the vibratory plate is supplied without fuel and
oil in it.
Fuel the vibratory plate as described under "Fuelling" in the
"Motor Operating Instructions"
Oil guard
The motor of the vibratory plate is equipped with an oil guard that
protects the motor against damage if the oil level is too low.
The motor shuts off on its own if the oil level is too low. Replenish
motor oil in this case as described in the section "Checking the motor
oil level" in the motor's operating instructions.
Please refer to the "Motor Operating Instructions" for
more information on the motor.
Start-up
Check that the machine is completely and correctly assembled.
Before each use, check
the machine for possible damage:
loose fasteners
Make sure that the ON/OFF switch, the clutch, the throttle lever
and the machine work properly.
Do not use any device where the switch cannot be switched
on and off. Damaged switches must be repaired or replaced
immediately by customer service.
The engine of the machine is supplied without gasoline and
oil in it. Fuel the device as described under "Fuelling".
Please refer to the "Engine Operating Instructions" for more
information on starting the motor.
Before start of work
Before starting any work ensure the following:
You may not start to operate the machine until you have read these
operating instructions, observed all the instructions given and
installed the machine as described!
Provide for a safe and clean workplace.
Before starting your work make sure that:
the device is in good and safe condition
all screw connections are firmly tightened
no other persons (children) or animals stay close the working
area
you can always step back without any barriers,
you always have a secure standing position.
Working with the vibratory plate
The device can be used to compact small and medium-size
areas.
Do not work on concrete-covered surfaces or very hard, dry
and dense soil.
The device will then start knocking on the surface instead of vibrating,
which could cause damage to the vibratory plate and the motor.
Undercarriage
The vibratory plate is equipped with an undercarriage for easier
transport. Swivel the undercarriage to the working position before
starting work.
Pull out the securing pin (8).
Swivel the chassis (9) under the vibratory plate.
19
Quicklinks ausblenden:
Werbung
Kapitel
Inhaltsverzeichnis
