Transport (Fig. 13); Maintenance; Storage; Electrical Connection - Parkside PKS 1500 B3 Bedienungs- Und Sicherheitshinweise Originalbetriebsanleitung

9.9 Replacing laser batteries (fig. 11)
• Remove the laser battery cover (34). Remove the 2 batteries.
• Replace both batteries with the same or an equivalent type.
Make sure that they are inserted with the same polarity as
the used batteries.
• Close the battery cover.
9.10 Switch ON / switch OFF the laser (fig. 11)
To switch on:
Move the ON/OFF switch (33) of the laser to the "1" position.
A laser line is projected onto the material you wish to process,
providing an exact guide for the cut.
To switch off:
Move the ON/OFF switch of the laser to the "0" position.
9.11 Adjusting the laser (fig. 12)
If the laser (35) ceases to indicate the correct cutting line, you
can readjust the laser. To do so, open the screws (36) and set
the laser by moving sideways to that the laser beam strikes the
teeth of the saw blade (6).
9.12 Using the clamping handle (fig. 1/2)
The height of the clamping device (15) can be adjusted via the
set screw (16).
• Lower the clamping device onto the workpiece.
• Tighten the set screw (16) firmly.
• Turn the clamping handle (24) clockwise to clamp the work-
piece.
• To release the workpiece, proceed in reverse order.

10. Transport (fig. 13)

• Tighten the set screw (7) in order to lock the rotary table (13)
• Press the machine head (4) downwards and secure with the
locking bolt (25). The saw is now locked in the lower posi-
tion.
• Carry the equipment by the transport handle (37).
• When reassembling the equipment proceed as described
under section 8 - 9.

11. Maintenance

m Warning!
Prior to any adjustment, maintenance or service work discon-
nect the mains power plug!
General maintenance measures
Wipe chips and dust off the machine from time to time using a
cloth. In order to extend the service life of the tool, oil the rotary
parts once monthly. Do not oil the motor.
When cleaning the plastic do not use corrosive products.
Cleaning the moving saw blade guard safety de-
vice (5)
Always check the saw blade guard for debris before using the
machine.
Remove old sawdust and splinters using a brush or similar tool.
Replacing the table insert (fig. 14)
Danger!
With a damaged table insert (10) there is a risk of small parts
getting stuck between table insert and saw blade, blocking the
saw blade.
Immediately replace damaged table inserts!
1. Remove table insert screws (E).
2. Remove table insert.
3. Install new table insert.
4. Tighten the table insert screws (E).
Brush inspection
Check the carbon brushes after the first 50 operating hours
with a new machine, or when new brushes have been fitted.
After carrying out the first check, repeat the check every 10
operating hours.
If the carbon is worn to a length of 6 mm, or if the spring or
contact wire are burned or damaged, it is necessary to replace
both brushes. If the brushes are found to be usable following
removal, it is possible to reinstall them.
When servicing the carbon brushes, open the two latches coun-
terclockwise (as shown in figure 15). Then remove the carbon
brushes.
Replace the carbon brushes in the reverse order.
Service information
Please note that the following parts of this product are sub-
ject to normal or natural wear and that the following parts are
therefore also required for use as consumables.
Wear parts*: carbon brushes, saw blade, table inserts, saw-
dust bags
* Not necessarily included in the scope of delivery!

12. Storage

Store the device and its accessories in a dark, dry and frost-
proof place that is inaccessible to children. The optimum stor-
age temperature is between 5 and 30˚C.
Store the electrical tool in its original packaging.
Cover the electrical tool in order to protect it from dust and
moisture.
Store the operating manual with the electrical tool.

13. Electrical connection

The electrical motor installed is connected and
ready for operation. The connection complies with
the applicable VDE and DIN provisions. The cus-
tomer's mains connection as well as the extension
cable used must also comply with these regula-
tions.
Important information
In the event of an overloading the motor will switch itself off. Af-
ter a cool-down period (time varies) the motor can be switched
back on again.
GB/IE 11