Selecting The Desired Temperature; Solving Problems - Gastroback 42436 Design Wasserkocher Cool Touch Bedienungsanleitung

is illuminated. After 2 seconds, the actual water temperature is shown on the dis-
play. The appliance is now ready for operation (standby mode).
WARNING – RISK OF SCALDS:
get hot during operation. Only touch the kettle at the operating elements and handle.
Even with the lid closed properly, hot steam could escape from under the lid during ope-
ration and some minutes thereafter. Do not hold your face, hands, or other parts of your
body, or any delicate objects over or directly beside the kettle, if the kettle is still hot.
Note:
The »Design Kettle Cool Touch« is no measuring appliance. There may be differences
between the temperature displayed on the display and the actual temperature of the
water. Using the temperature selection buttons, you may change the set temperature
any time you like before and during operation (see below: 'Selecting the Desired
Temperature').
Simply press the ON/OFF button to start the boiling cycle. On the display the set
temperature is shown and the kettle starts heating immediately. With none of the
temperature selection buttons pressed, the set temperature is always "100"°C.
As soon as the water reaches the set temperature, the kettle turns off. To activate
keep warm function press the „keep warm" button. Keeping the water hot for at
up to 30 minutes. Thereafter, the kettle will shut off and the display gets dark.
IMPORTANT: The maximum water temperature of the keep warm function is limited
to 90 °C, because water will evaporate too quickly when kept at a higher tempera-
ture. Thus, there would be a high risk of overheating when the water level falls below
the minimum amount of 0,5 litres.
Note:
You may cancel the operating cycle at any time by removing the kettle from its
base, or by pressing the ON/OFF button. Do not leave the kettle in keep warm
operation needlessly to avoid useless energy loss.

SELECTING THE DESIRED TEMPERATURE

The electronic »Design Kettle Cool Touch« can heat water to a selected temperature
in the range from 35°C to 100°C (boiling temperature). The set temperature may be
modified at any time during operation (heating up or keeping warm) or in standby
mode. However, please keep in mind, that the actual water temperature could rise
above the set temperature after heating. This will occur especially with a low tempe-
rature selected and/or only a small amount of water in the kettle.
1. Press the temperature selection buttons „KEEP WARM" or „TEMP" several times
until the desired temperature is shown on the display.
38
The upper part of the exterior of the kettle will
2. If the kettle is in standby mode, press the ON/OFF button to start operation. If
the kettle is in operation already, the thermostat of the kettle will automatically be
adjusted to the newly set temperature.

SOLVING PROBLEMS

If any problems occur during operation, you will find the solution in the following table.
Problem Reason
The display remains The appliance is not live. Ensure that the appliance is connected to a suitable
dark. No signal
sounds, when pla-
cing the kettle on
the base.
A severe problem
occurred.
The kettle is placed
The automatic shut-off
on the base and has been triggered.
plugged in, but the
display is dark.
The appliance is The overheat protection
live, but the water system has been trig-
is not heated.
gered.
Water accumulates
There is too much water
under the base or in the kettle.
runs down on the
exterior of the
You spilled some water
kettle.
when filling or moving
the kettle.
The kettle is leaking.
The Solution
wall power outlet. Ensure that the wall power outlet is
live by connecting a lamp.
Check, if the kettle is connected correctly to the base.
Turn it a little.
Immediately take the kettle off the base and unplug
the base. Get in contact with an authorised service cen-
tre for examination and repair.
If no button has been pressed for 30 minutes, the
kettle will switch OFF completely to save energy. Simp-
ly press a button to reactivate the display.
The kettle has been operated without water or with too
little water. Empty the kettle and leave it cool down for
at least 20 minutes. Thereafter, fill the kettle with at
least 0.5 litres of cold water and try again.
Too much scale is covering the heating elements, cau-
sing overheating. De-scale the kettle (see: 'De-scaling
the Kettle').
Immediately unplug the appliance. Then wipe dry the
appliance completely. Always observe the MAX filling
level when filling (1.5 litres).
Immediately unplug the appliance. Then wipe dry the
appliance completely. Ensure not to spill water on the
exterior of the kettle during filling. Always ensure to
hold the kettle level when it is filled.
Immediately unplug the appliance and wipe dry the
appliance completely. Then check the kettle for leaka-
ge. Do not use the appliance, if the kettle is leaking.
39