Residual Risks; Technical Data; Before Starting The Equipment - Scheppach DH1300PLUS Originalbetriebsanleitung

• Keep your cutting tools sharp and clean. Care-
fully maintained cutting tools with sharp cutting
edges will jam less and are easier to control.
• Make sure to use electric tools, accessories,
attachments, etc. in accordance with these in-
structions. Take the conditions in your work
area and the job in hand into account. Using
electric tools for any purpose other than the one
for which they are intended can lead to dangerous
situations.
Service
• Have your electric tool repaired only by trained
personnel using only genuine spare parts. This
will ensure that your electric tool remains safe to
use.
Safety Information for hammer
• Wear ear protection. The impact of noise can
cause damage to hearing.
• Use the additional handles supplied with the
tool. Losing control of the tool can cause injuries.
• Hold the equipment by the insulated handles
when carrying out work during which the plug-
in tool could strike concealed power cables or
its own mains lead. Contact with a live cable can
also make the metal parts of the equipment live and
will cause an electric shock.
Do not lose these safety instructions

Residual risks

Even if you use this electric power tool in ac-
cordance with instructions, certain residual
risks cannot be rules out. The following haz-
ards may arise in connection with the equip-
ment's construction and layout:
• Lung damage if no suitable protective dust mask is
used.
• Damage to hearing if no suitable ear protection is
used.
• Health damage caused by hand-arm vibrations if
the equipment is used over a prolonged period or is
not properly guided and maintained.

Technical data

Mains voltage
Power input
Idling speed
Blow rate
Drilling capacity in con-
crete/stone (max.)
Protection class
Weight
Danger!
Sound and vibration
Sound and vibration values were measured in accordance
with EN 60745.
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
220-240 V~ 50 Hz
1250 W
850 min
-1
4500 bpm
30 mm
II
4.9 kg
L sound pressure level
pA
K uncertainty
pA
L sound power level
WA
K uncertainty
WA
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Total vibration values (vector sum of three directions)
determined in accordance with EN 60745.
Main handle
Hammer drilling in
Concrete: a = 13.59 m/s
2
h(HD)
Additional handle
Hammer drilling in
Concrete: a = 11.265 m/s
h(HD)
Main handle
Chiselling: a = 14.3 m/s
h(CHeq)
Additional handle
Chiselling: a = 14.51 m/s
h(CHeq)
The specified vibration value was established in ac-
cordance with a standardized testing method. It may
change according to how the electric equipment is
used and may exceed the specified value in excep-
tional circumstances.
The specified vibration value can be used to compare
the equipment with other electric power tools.
The specified vibration value can be used for initial
assessment of a harmful effect.
Keep the noise emissions and vibrations to a min-
imum.
• Only use appliances which are in perfect working
order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever necessary.
• Switch the appliance off when it is not in use.
• Wear protective gloves.

Before starting the equipment

Before you connect the equipment to the mains sup-
ply make sure that the data on the rating plate are
identical to the mains data.
Warning!
Always pull the power plug before making adjust-
ments to the equipment.
Check the drilling point for concealed electrical ca-
bles, gas and water pipes using a cable/pipe detector.
90.9 dB(A)
3 dB(A)
101.9 dB(A)
3 dB(A)
, K = 1.5 m/s
2
, K = 1.5 m/s
2 2
, K = 1.5 m/s
2 2
, K = 1.5 m/s
2 2
13 І 80