Homelite F-2035 Bedienungsanleitung Seite 16

F2035 _17 lgs 5/12/03
GB
F D E
SPECIFICATIONS
Engine Speed (rotational frequency)
at recommended max.
spindle rotational frequency
Engine speed (rotational frequency)
at idle
Fuel consumption (in accordance
with ISO 8893) at max.
engine performance
Specific fuel consumption
(in accordance with ISO 8893)
at max. engine performance
Vibration level idling
- Front Handle
- Rear Handle
Vibration level racing
- Front Handle
- Rear Handle
Sound pressure level
(in accordance with EN ISO 11806:
1997, ISO 7917:1987)
Sound power level (in accordance
with ISO 10884)
DESCRIPTION
1. MUFFLER GUARD
2. CHOKE LEVER
3. THROTTLE CONTROL
AND REAR HANDLE
4. STARTER GRIP
5. THROTTLE TRIGGER
6. IGNITION SWITCH
7. DRIVE SHAFT HOUSING
8. FRONT HANDLE
9. GRASS DEFLECTOR
10. STRING HEAD
11. EDGER GUIDE
12. BOLT
13. WING NUT
14. REAR HOUSING
15. SCREWS
16. BENT OF MUFFLER GUARD
17. OPENING IN REAR HOUSING 40. PULL COVER TO OPEN
18. EDGER GUIDE PIECES
19. LOCK WASHER
20. FLAT WASHER
21. SHORT BOLT
22. ASSEMBLED EDGER GUIDE 45. "H" HIGH NEEDLE
11:28 Page 11
I P NL S DK
English
INSTRUCTIONS
12,500/min -1
-1
2,000-2,500/min
0.48 kg/h
PACKING LIST FOR OWNER'S KIT
0.46 kg/h
2
2.8 m/s
2.5 m/s 2
2
4.5 m/s
2
4.4 m/s
FRONT HANDLE (Fig. 2)
99 LpA (dBA)
1. Remove the front handle (8), bolt (12), and wing nut
113 LwA (dBpA)
2. Install the front handle onto the top side of the drive
3. Place the bolt through the front handle as shown, then
23. TABS
24. LONG BOLT
4. Tighten wing nut securely.
25. THROTTLE INTERLOCK
26. PRIMER BULB
NOTE: Do not attempt to remove or modify the spacer.
27. RUN POSITION
This spacer limits the upper position of the handle grip.
28. HALF CHOKE POSITION
29. CHOKE POSITION
MUFFLER GUARD ASSEMBLY (Fig. 3)
30. SPOOL RETAINER
31. SLOTS
1. Remove muffler guard (1) and two screws from the
32. SPRING
33. EYELETS
2. Attach the muffler guard to the rear housing (14).
34. SPOOL
35. ARROWS ON SPOOL
NOTE: Make sure the bent end of the muffler guard (16)
36. ANCHOR HOLE
fits securely into the opening of the rear housing (17).
37. FIRST STRING
3. Install two screws.
38. SECOND STRING
39. LATCH
4. Tighten screws securely.
41. FILTER
EDGER GUIDE ASSEMBLY (Fig. 4)
42. AIR FILTER COVER
43. IDLE SPEED SCREW
1. Assemble the two plastic pieces of the edger guide
44. "L" LO NEEDLE
2. Slide the edger guide to adjust it to the desired
3. Tighten the wing nut securely.
11
N FIN GR H
UNPACKING
Carefully remove the product from the carton.
Inspect the product to make sure no breakage or
damage occurred during carriage.
Do not discard the packing material until you have
inspected and operated the product.
Grass deflector (9)
Front Handle (8)
Trim'n Edge Kit
Muffler guard (1), torx wrench and screws (15)
Hardware
Operator's manual
ASSEMBLY
(13) from the Owner's Kit.
shaft housing (7) and move it to a comfortable position.
install the wing nut.
owner's kit.
(18) together using the short bolt (21), flat washer (20),
lock washer (19) and wing nut.
trimming length.
CZ RUS RO PL