Inhaltsverzeichnis
Werbung
Installation and Operating Instructions
EN
m
DANGER
+
IMPORTANT
m
WARNING
ATTENTION
Central ventilation units AIR1 XH
The controller of this product contains batteries. According to the battery law (BattG) we are obliged to inform you
about the following:
Batteries and rechargeable batteries must not be disposed of with household waste. You are legally obliged to return used
batteries and accumulators. You can return batteries and accumulators free of charge to retailers or municipal collection points.
Batteries or rechargeable batteries that contain harmful substances are marked with a crossed-out dustbin symbol.
Under the garbage can symbol is the chemical designation of the pollutant.
Cd for cadmium / Pb for lead / Hg for mercury
Think of our environment, with the return you make a substantial contribution to environmental protection!
2�2 Mechanical assembly
m
Danger to life due to electric shock
The installation and connection of the unit may only be carried out by qualified specialist personnel. The electrical
connections must be carried out by a person who has proper professional training and experience in the relevant acci-
dent prevention regulations, as well as other generally recognised safety and occupational health codes, with authori-
sation to perform work on the unit.
2�2�1 General mechanical assembly
The central ventilation unit AIR1 XH must be installed in the upright position. Due to noise levels, which change depen-
ding on system pressure, it is recommended that the compact ventilation unit is installed in the utility room or storage
room. It must be ensured that there is a waste water connection in the installation area. In this respect, please consider
the condensation outlet information!
The assembly should take place in such a way to enable the shortest possible ventilation ducts and trouble-free
connection to the unit. Tight bends result in increased pressure losses and flow noises.
The unit can be turned 180° for optimal installation, so that the inlets and outlets for the outside air/exhaust air and
extract air/supply air can be on the left or right side of the unit. With regard to these properties, bends and long pipe
sections are not required. In addition, the heat loss is reduced and the system efficiency is increased.
Important information:
– The ventilation ducts must not become kinked.
– The connections to the connectors must be firm and tight.
– The flange connections must be leakproof and firm.
– If necessary, anti-vibration mounts can be used on site between the base of the unit and the floor.
m
Risk of injury due to moving parts!
If there is no duct connection, the exhaust air discharge hood (accessories) must be mounted on the exhaust air side
to prevent contact with moving parts.
Ensure that the unit is positioned on a flat surface before the start of installation work.
Assembly area
The following criteria must be observed when installing the unit to ensure easy accessibility for maintenance and main-
tenance work (Fig.4).
A: Minimum distance servicing the terminal box
B: Width of unit
C: Minimum distance for opening the service door
D: Height of unit (incl. terminal box)
B
Gerätetyp
A
B
AIR 1 XH 1000
600
685
AIR 1 XH 1500
600
695
It must be ensured that there is sufficient space for the maintenance work� For this reason, the dimensions
AIR 1 XH 2500
600
915
AIR 1 XH 3500
600
1017
must first be marked before the unit is assembled�
AIR 1 XH 4500
600
1070
AIR 1 XH 5500
600
1280
AIR 1 XH 7000
600
1580
AIR 1 XH 8500
600
1930
Gerätemaße
Maß festgelegt
Geräte Maß D
!
C
Maße in mm
C
D
885
1230
895
1425
1115
1505
1217
1644
1270
2065
1480
2065
1780
2065
2130
2065
Geräte Maß D
Geräte Maß max. E
+ 200 mm
7
Unit type
Dimensions (mm)
A
B
AIR1 XH 1000
600
785
600
795
AIR1 XH 1500
600
1015
AIR1 XH 2500
AIR1 XH 3500
600
1173
AIR1 XH 4500
600
1226
AIR1 XH 5500
600
1436
AIR1 XH 7000
600
1736
AIR1 XH 8500
600
2086
Fig�4
C
D
985
1010
995
1205
1215
1424
1375
1845
1425
1845
1635
1845
1935
1845
2285
1845
Quicklinks ausblenden:
Werbung
Kapitel
Inhaltsverzeichnis
