RECARO MONZA NOVA 2 Montage- Und Gebrauchsanleitung Seite 8

Install the child seat in the vehicle in such a way that it is not clamped by the front seats or
∙
the vehicle door.
∙ The child seat must not be modified in any way, and the instructions for installation and use
must be followed carefully, otherwise your child could be put at risk while travelling.
∙ The belts must not be twisted or trapped and must be completely tightened.
IMPORTANT: Ensure that the lap belt in particular is tight and fitted as low as possible
∙
across the child's pelvis.
∙ After an accident, the child seat must be removed and tested in the factory and, if
necessary, replaced.
∙ Very bulky items of clothing must be removed prior to securing the child in.
∙ Always ensure that items of luggage and other objects are adequately secured, particularly
those on the parcel shelf, as these could cause injury in the event of a collision.
∙ Always set a good example and always use your seat belt. An adult who is not wearing a
seatbelt can also endanger your child.
Notice: Only original accessories or replacement parts may be used.
∙
∙ Never leave your child unattended.
∙ Always strap your child in.
Protect the child seat from direct sunlight in order to avoid your child being burnt by it and to
∙
preserve the color of the cover.
∙ The child seat must not be used without the cover. The cover must never be replaced with a
cover which has not been recommended by the manufacturer, since this cover comprises an
integral part of the seat safety system.
∙ IMPORTANT: Ensure at installation and use of the SEATFIX connectors that both arms are
on equal length. The child seat must not be installed crooked.
2. Installing the child car seat
2.1 Installing in the vehicle without the Seatfix
Place the RECARO Monza Nova 2 / Seatfix, Monza Nova Evo / Seatfix on the intended vehic-
le seat. This must be fitted with a three-point seat belt that has been tested according to
ECE-R16 or a comparable safety standard. Details on your vehicle's suitability for child car
seats are also given in the vehicle manual. (fig. 2).
2.2 Installing in the vehicle with the Seatfix
∙ Attention: Always use the vehicle's 3-point seat belt when securing your child! The Seatfix
system improves the level of protection in the event of a side impact, and secures the seat
when it is not in use. Insert the insertion aids through the upholstery slit in the backrest and
seat and attach to the Isofix attachment brackets. This is not necessary where insertion aids
are already permanently installed. Ensure that the open side is facing upwards. (fig. 3).
To install the Seatfix in the car, you have to pull out the Seatfix-connectors. For each side
∙
- press the locking button and pull out the Seatfix-connector (A) fully. Release the locking
button again. (fig. 4).
Press each seatfix-connector onto the ISOFIX-anchors.
∙
∙ Check that the green mark is visible on both connectors and that they are firmly locked by
pulling on both sides of the child seat. (fig. 5).
IMPORTANT: Ensure at installation and use of the Seatfix connectors that both arms are on
∙
equal length. The child seat must not be installed crooked.
∙ Push the child seat, with the locking buttons pressed down, towards the vehicle seat until
the backrest is positioned up against the backrest of the vehicle seat. (fig. 6).
∙ After an accident at a speed exceeding 10 km / h , the child seat may have been damaged. It is
therefore imperative that the seat is checked by the manufacturer and, if necessary, replaced.
Never use the child seat when the Seatfix connectors have been released!
∙
3. Adjusting the child car seat
The size of the seat can be adjusted while the lever at the back of the headrest is pulled up.
(fig. 7). Please also refer to Chapter 4. "Strapping the child in" .
DE
EN
FR
NL
SL
PL
SV
NO
DA
FI
AR
LT
LV
IT
HR
ES
PT
TR
EL
CS
SK
UK
ET
RO
SR
RU
HU
HE
JA
TH
ID
TW
7