Dolmar MS-252 Originalbetriebsanleitung Seite 4

Start the Brush Cutter/String trimmer only in accordance with the instructions.
– Do not use any other methods for starting the engine!
– Use the Brush Cutter/String trimmer and the tools only for such applications as
specified.
– Only start the Brush Cutter/String trimmer engine, after the entire assembly
is done. Operation of the device is only permitted after all the appropriate
accessories are attached!
– Before starting make sure that the cutting tool has no contact with hard objects
such as branches, stones etc. as the cutting tool will revolve when starting.
– The engine is to be switched off immediately in case of any engine problems.
– Should the cutting tool hit stones or other hard objects, immediately switch off the
engine and inspect the cutting tool.
– Inspect the cutting tool at short regular intervals for damage (detection of hairline
cracks by means of tapping-noise test).
– Operate the Brush Cutter/String trimmer only with the shoulder strap attached
which is to be suitably adjusted before putting the Brush Cutter/ String trimmer
into operation. It is essential to adjust the shoulder strap according to the user's
size to prevent fatigue occurring during use. Never hold the cutter with one hand
during use.
– During operation always hold the Brush Cutter/String trimmer with both hands.
Always ensure a safe footing.
– Operate the Brush Cutter/String trimmer in such a manner as to avoid inhalation
of the exhaust gases. Never run the engine in enclosed rooms (risk of gas
poisoning). Carbon monoxide is an odorless gas.
– Switch off the engine when resting and when leaving the Brush Cutter/ String
trimmer unattended, and place it in a safe location to prevent danger to others or
damage to the machine.
– Never put the hot Brush Cutter/String trimmer onto dry grass or onto any
combustible materials.
– The cutting tool has to be equipped with it's appropriate guard.
Never run the cutter without this guard!
– All protective installations and guards supplied with the machine must be used
during operation.
– Never operate the engine with faulty exhaust muffler.
– Shut off the engine during transport.
– When transporting the equipment, always attach the cover to the cutting blade.
– Ensure safe position of the Brush Cutter/String trimmer during car transportation
to avoid fuel leakage.
– When transporting the Brush Cutter/String trimmer, ensure that the fuel tank is
completely empty.
– When unloading the Brush Cutter/String trimmer from the truck, never drop the
Engine to the ground or this may severely damage the fuel tank.
– Except in case of emergency, never drop or cast the Brush Cutter/String trimmer
to the ground or this may severely damage the Brush Cutter/String trimmer.
– Remember to lift the entire equipment from the ground when moving the
equipment. Dragging the fuel tank is highly dangerous and will cause damage
and leakage of fuel, possibly causing fire.
– If the equipment gets heavy impact or fall, check the condition before continuing
work. Check the fuel system for fuel leakage and the controls and safety devices
for malfunction. If there is any damage or doubt, ask our authorized service center
for the inspection and repair.
Refuelling
– Shut off the engine during refuelling, keep away from open flames and do not
smoke.
– Avoid skin contact with mineral oil products. Do not inhale fuel vapor. Always
wear protective gloves during refuelling. Change and clean protective clothing at
regular intervals.
– Take care not to spill either fuel or oil in order to prevent soil contamination
(environmental protection). Clean the Brush Cutter/String trimmer immediately
after fuel has been spilt.
– Avoid any fuel contact with your clothing. Change your clothing instantly if fuel
has been spilt on it (to prevent clothing catching fire).
– Inspect the fuel cap at regular intervals making sure that it can be securely
fastened and does not leak.
– Carefully tighten the fuel tank cap. Change location to start the engine (at least
3 meters away from the place of refuelling).
– Never refuel in closed rooms. Fuel vapors accumulate at ground lever (risk of
explosions).
– Only transport and store fuel in approved containers. Make sure the fuel stored is
not accessible to children.
• Resting
• Transport
• Refuelling
• Maintenance
• Tool Replacement
4
3 meters