EINHELL GE-LM 36/4in1 Li Originalbetriebsanleitung Seite 38

11a/Item H) at the housing recess (Item D). Insert
the hex key (Item 26) into the recesses and turn
the cutting line unit (Item C) clockwise (a) off the
gear axle.
5.2.2.b Fitting the cutting line unit
The cutting line unit must be refi tted for later use
as a trimmer. Turn the cutting line unit (Item C)
counter-clockwise (b) onto the gear axle as far as
the housing recess (Item D) until you can see the
recess of the fl ange (Fig. 11a/Item H). Insert the
hex key (Item 26) into the recesses and turn the
cutting line unit (Item C) counter-clockwise. Re-
move the hex key. Check whether the cutting line
unit can rotate freely. If this is not the case, have
the mechanism checked by an expert.
5.2.3 Guard hood for use with the cutting bla-
de (Fig. 9- 10)
Caution! The cutting line blade guard hood (Item
23a) must be removed when you want to work
with the cutting blade. Take care not to cut your-
self on the cutting line blade (Item 23c).
Slacken the two retaining screws (Item E) on the
cutting line blade cover (Item 23a). Start at the
side and carefully press in the lugs (Item 23b) and
gradually pull off the cutting line blade cover (Item
23a).
5.2.4 Guard hood for use with the cutting line
(Fig. 9-10)
Caution! The cutting line blade guard hood (Item
23a) must be fi tted when you want to work with
the cutting line. Take care not to cut yourself on
the cutting line blade.
Start at the side and press the lugs (Item 23b) in
again. Fasten them with the two retaining screws
(Item E).
5.2.5 Fitting/removing the cutting blade
Remove the cutting line unit as described in sec-
tion 5.2.2.a.
5.2.5.a Fitting the cutting blade
(Fig. 11a – 11f)
Important! If the fl ange (Item 30) between the
cutting blade and the gear housing (see the de-
tailed drawing 11g/Item 30) slips off the gear axle
(Item F) while dismantling the cutting line unit,
push it back onto the gear axle (Item F). The open
fl ange side must face the gear housing.
1. Place the cutting blade (Item 25) onto the
fl ange (Item 30) in central position.
2. Fit the pressure plate (Item 27) with the high-
er edge facing the cutting blade. (See also the
Anl_GE_LM_36_4in1_Li_SPK9.indb 38
GB
detailed drawing 11g.)
3. Put on the pressure plate cover (Item 28) (see
also the detailed drawing 11g)
4. Screw on the hex nut M10 (Item 29) with its
left-hand thread (see also the detailed dra-
wing 11g). Warning! For safety reasons, self-
locking nuts are allowed to be used only once
without exception.
5. Insert the hex key (Item 26) into the recess of
the gear housing and fl ange. Tighten the hex
nut using the multifunction tool size 19 (Item
24) securely.
6. Check that the cutting blade rotates freely
after you remove the assembly tools. If this is
not the case, have the mechanism checked
by an expert.
7. Remove the blade guard covers (Item 25a).
Warning! Take care not to injure yourself on
the cutting blade.
5.2.5.b Removing the cutting blade
Remove the cutting blade in reverse order to that
described in section 5.2.5.a.
5.2.6 Fitting the trimmer/scythe module on
the motor unit (Fig. 12)
Push the connecting tube (Item 8) of the fully pre-
assembled trimmer/scythe module and the exten-
sion tube (Item 12) of the pre-assembled motor
unit into one another and screw them together
with the union nut (Item 7). To dismantle, proceed
in reverse order.
5.2.7 Adjusting the cutting height (Fig. 13)
To establish the optimum length of the harness,
put on the harness (see point 6.1.1) and make
a few swinging movements without starting the
motor.
5.3 Assembly/adjustments of the pole-moun-
ted pruner
Danger! Do not fi t the battery until the pole-
mounted pruner has been fully assembled and
the chain tension has been set. Always wear
protective gloves when working on the pruner to
protect yourself against injury. Use the cutter rail
guard (Fig. 2/Item 20).
5.3.1 Converting the connecting tube
(Fig. 14-16)
To be able to use a diff erent module (e.g. the
pole-mounted pruner) you must convert the con-
necting tube (Fig. 2/Item 8).
1. Push the lock release (Item 9) forward and
turn the union nut (Item 8a). Pull the connec-
- 38 -
20.11.2020 08:35:34