Transportation And Storage; Maintenance - Ryobi RCS5133CB Originalanleitung

TRANSPORTATION AND STORAGE

■
Stop the engine, engage the chain brake, and
disconnect the spark plug wire from the spark plug.
Allow the product to cool down before storing or
transporting.
■
Clean all foreign material from the product.
■
Drain all fuel from tank into a container approved for
petrol. Remember to properly replace and tighten the
fuel mix cap.
■
Run the engine until it stops. This will remove all fuel-
lubricant mix that could become stale and leave varnish
and gum in the fuel system.
■
Drain all bar and chain lubricant from tank into a
container approved for lubricant. Remember to properly
replace and tighten the chain lubricant cap.
■
Always fit guide bar cover before storing the product, or
during transportation.
■
Store the product in a cool dry and well-ventilated
place that is inaccessible to children. Keep away from
corrosive agents such as garden chemicals and de-
icing salts. Do not store outdoors.
■
When carrying the product for short distance (from one
working area to the next), always apply the chain brake
so that the saw chain is restricted from movement.
■
When transporting the product, secure it against
movement or falling to prevent injury to persons or
damage to the product.
■
Never carry or transport the product while the engine
is running.
Abide by all government and local regulations for the safe
storage and handling of petrol. Excess fuel should be used
in other 2-cycle engine powered equipment.

MAINTENANCE

Always keep the product in good working condition.
WARNING
Use only original manufacturer's replacement parts,
accessories and attachments. Failure to do so can
cause possible injury, poor performance and may void
your warranty.
WARNING
Servicing requires extreme care and knowledge
and should be performed only by a qualifi ed service
technician. For servicing and repairs, bring the product
to an authorised service centre. When servicing, use
only original replacement parts.
WARNING
Before inspecting, cleaning, or servicing the product,
stop the engine, engage the chain brake, and disconnect
the spark plug wire from the spark plug. Failure to follow
these instructions can result in serious personal injury or
property damage.
All manuals and user guides at all-guides.com
■
■
■
■
■
■
REPLACING GUIDE BAR AND SAW CHAIN
See page 329 - 330.
1. Stop the product. Wear protective gloves.
2. Disengage the chain brake.
3. Remove the bar mounting nuts using the combination
4. Remove the chain cover.
5. Remove the bar and saw chain from the product.
6. Put the new chain in the correct direction onto the bar
7. Attach the bar to the chain saw and loop the chain
8. Replace the chain cover and bar mounting nuts.
9. Finger-tighten the bar mounting nuts. The bar must be
10. Adjust the chain tension. Refer to the "Adjusting chain
11. Hold the tip of the guide bar up and tighten the bar
CLEANING THE AIR FILTER
See page 333 - 334.
1. Push down on the knob on the top of the air filter cover
2. Blow or brush as much loose dirt and sawdust from
NOTE: Ensure the choke lever is in the full-choke position
to keep the carburettor from being contaminated.
3. Using the combination wrench provided or a flathead
4. Position a flathead screw driver between the tabs and
5. Lift the air filter off the air filter base.
You may only make adjustments or repairs described
in this manual. For other repairs, contact the authorised
service centre.
Consequences of improper maintenance may cause
the chain brake and other safety features to not function
correctly, thus increasing the potential for serious injury.
Keep the product professionally maintained and safe.
Sharpening the chain safely is a skilled task. Therefore
the manufacturer strongly recommends that a worn
or dull chain is replaced with a new one, available
from your authorised service centre. The part number
is available in the product specification table in this
manual.
Follow instructions for lubricating and chain tension
checking and adjustment.
After each use, clean the product with a soft dry cloth.
Check all nuts, bolts and screws at frequent intervals
for security to ensure the product is in safe working
condition. Any part that is damaged should be properly
repaired or replaced by an authorised service centre.
wrench provided.
and make sure that the drive links are aligned in the
bar groove.
around the drive sprocket.
free to move for chain tension adjustment.
tension" section.
mounting nuts securely.
and turn it counterclockwise to unlock. Lift the air filter
cover straight up to remove; set aside.
around the carburettor and chamber as possible.
screwdriver, remove the screw securing the air filter.
twist to remove the air filter.
Choose one of the following cleaning options:
●
To lightly clean, tap the filter against a smooth, flat
surface to dislodge most of the saw dust and dirt
particles.
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
English | 7