Safety System; Safety Pictograms - Anest Iwata DDP Serie Bedienungsanleitung

DPS-70 C - DPS-70 CN DIAPHRAGM PUMPS
EN
6.2 ALL DPS VERSIONS
STAND TYPE
DDP version mounted on stand, with paint regulator, 2 air regulators (for pump and gun),
dip tube with filter, fluid recirculation, 1 overpressure valve, ball valve with exhaust hole.
• PR-5BL paint pressure regulator for DPS 70-1C.TE
• PR-5BLN paint pressure regulator for DPS 70-1CN.TE
TANK MOUNT TYPE
DDP version mounted on tank mount lid (without tank) with paint regulator, 2 air regulators (for
pump and gun), dip pipe with filter (for 20L tank), fluid recirculation, overpressure valve, ball
valve with exhaust hole.
• PR-5BL paint pressure regulator for DPS 70-2C.TE
• PR-5BLN paint pressure regulator for DPS 70-2CN.TE
CART TYPE
DDP version mounted on wheel cart with paint regulator, 2 air regulators (for pump and gun), dip
tube with filter, fluid recirculation, 1 overpressure valve, ball valve with exhaust hole.
• PR-5BL paint pressure regulator for DPS 70-3C.TE
• PR-5BLN paint pressure regulator for DPS 70-3CN.TE
WALL MOUNT TYPE
DDP version mounted on wall mounting bracket with paint regulator, 2 air regulators (for
pump and gun), dip tube with filter, fluid recirculation, 1 overpressure valve, ball valve with
exhaust hole.
• PR-5BL paint pressure regulator for DPS 70-4C.TE
• PR-5BLN paint pressure regulator for DPS 70-4CN.TE
CART TYPE + HOPPER
DDP version mounted on wheel cart with paint regulators, 2 air regulators (for pump and
gun), plastic hopper (6 lt. with 50 mesh filter), fluid recirculation, 1 overpressure valve, ball
valve with exhaust hole.
• PR-5BL paint pressure regulator for DPS 70-36C.TE
• PR-5BLN paint pressure regulator for DPS 70-36CN.TE
8
DPS 70-1C.TE | DPS 70-1CN.TE
DPS 70-2C.TE | DPS 70-2CN.TE
DPS 70-3C.TE | DPS 70-3CN.TE
DPS 70-4C.TE | DPS 70-4CN.TE
DPS 70-36C.TE | DPS 70-36CN.TE
DPS-70 C - DPS-70 CN DIAPHRAGM PUMPS

6.3 SAFETY SYSTEM

Several safety systems have been conceived during the diaphragm pump design and manufacture to safeguard the operator,
as it prescribed by all applicable safety regulations.
SAFETY VALVE
A 7 bar calibrated safety valve is installed to ensure the pump working pressure does not
exceed the limits inside the feeding circuit.
Release hole
If the calibration pressure is exceeded, the valve opens by releasing the excess of air.
WARNING
DO NOT DISASSEMBLE THE SAFETY VALVE. ANY TAMPERING WITH COULD BE
DANGEROUS FOR THE OPERATOR AND COMPROMISE THE EQUIPMENT GOOD WORKING.
EXHAUST VALVE
In case of anomalies during working, turn 90° the exhaust valve lever. In this way the air supply will be interrupted and the
residual pressure inside the pump will be released.

6.4 SAFETY PICTOGRAMS

Some pictograms can be found on the pump with the safety warnings to follow by anyone who is going to use it.
WARNING
THE MANUFACTURING COMPANY IS NOT TO BE HELD RESPONSIBLE FOR DAMAGE OR ACCIDENTS TO PEOPLE
OR THINGS COMING FROM THE NON-COMPLIANCE WITH THE PRESCRIBED RULES.THE RESPONSIBILITY RESTS
ENTIRELY WITH THE OPERATOR HIM SELF.
ON
EN
OFF
9