Installation - IKEA FULLGÖRA Bedienungsanleitung

ENGLISH
Attention:
• Incompatibility with the "Fast Cool" function
To guarantee optimal performance, the "Vacation" and "Fast
Cool" functions cannot be used at the same time. Therefore, if
the "Fast Cool" function has been already engaged, it has to be
disengaged first to activate the "Vacation" function (and vice-
versa).
Fast Cool button
Using Fast Cool function it is possible to increase the cooling
capacity in the refrigerator compartment. The use of this
function is recommended when placing a very high quantity
of food in the refrigerator compartment. Press the Fast Cool
button to activate Fast Cool function. When activated, the Fast
Cool indicator turns on. The function is automatically disabled
after 6 hours, or can be manually disabled by pressing Fast Cool
button again.
Attention:
• Incompatibility with the "Vacation" function
To guarantee optimal performance, the "Vacation" and "Fast
Cool" functions cannot be used at the same time. Therefore, if

Installation

The appliance must be handled and installed by two or more
persons - risk of injury. Use protective gloves to unpack and install
- risk of cuts.
Installation, including water supply (if any), electrical
connections and repairs must be carried out by a qualified
technician. Do not repair or replace any part of the appliance
unless specifically stated in the user manual. Keep children away
from the installation site. After unpacking the appliance, make
sure that it has not been damaged during transport. In the
event of problems, contact the dealer or your nearest Aftersales
Service. Once installed, packaging waste (plastic, styrofoam parts
etc.) must be stored out of reach of children - risk of suffocation.
The appliance must be disconnected from the power supply
before any installation operation - risk of electric shock. During
installation, make sure the appliance does not damage the power
cable - risk of fire or electric shock. Only activate the appliance
when the installation has been completed.
Be careful not to damage the floors (e.g. parquet) when
moving the appliance. Install the appliance on a floor or support
strong enough to take its weight and in a place suitable for
its size and use. Make sure the appliance is not near a heat
When contacting our Service Provider, please state the codes
provided on your product's identification plate.
The model information can be retrieved using the QR-Code
reported in the energy label. The label also includes the model
identifier that can be used to consult the
https://eprel.ec.europa.eu database portal.
*On the rating plate the article number is 8 digits
Inspection check list
Please follow the inspection checklist before using your appliance.
If any answer is NOT please follow the relevant action.
Please remember to write down the product serial number and
article number as required and attach your receipt to this page.
Product serial number (rating plate) *
Product artical number (rating plate) **
Purchasing date
the "Vacation" function has been already engaged, it has to be
disengaged first to activate the "Fast Cool" function (and vice-
versa).
Turning off the sound alarm
To turn off the sound alarm, briefly press the
Profresh
This function automatically works to ensure the optimal
conditions to preserve the stored food. To deactivate the
"ProFresh", press and hold Fast Cool and Stop Alarm buttons at
the same time for 3 seconds until an audible signal sounds and
"ProFresh" icon turns off as confirmation that the feature has
been deactivated. To reactivate this function repeat the same
procedure.
Note: Deactivation of the function switch-off the FAN in the
fridge
To avoid food waste, please refer to the recommended To avoid
food waste, please refer to the recommended setting and
storage times found in the user manual.
source and that the four feet are stable and resting on the floor,
adjusting them as required, and check that the appliance is
perfectly level using a spirit level. Wait at least two hours before
switching the appliance on, to ensure that the refrigerant circuit is
fully efficient.
WARNING: When positioning the appliance, ensure the
supply cord is not trapped or damaged.
WARNING: To avoid a hazard due to instability, positioning
or fixing of the appliance must be done in accordance with the
manufacturer instructions. It's forbidden to place the refrigerator
in such way that the metal hose of gas stove, metal gas or water
pipes, or electrical wires are in contact with the refrigerator back
wall (condenser coil).
To guarantee adequate ventilation, leave a space on both
sides and above the appliance. The distance between the rear
of the appliance and the wall behind the appliance should be 50
mm, to avoid access to hot surfaces. A reduction of this space
will increase the Energy consumption of product. Please remove
the power cord from condenser hook during installation before
connecting product to power supply.
XXXXXXXXXXXXX
XXXXXXXXXXXXX
XXXXXXXXXXXXX XXXXXXXXX XXXXXXXXXXXXX
XXXXXXXXXXXXX XXXXXXXXXXXXX
XXXXX XXXXX XXXXX XXXXX
XXXXX XXXXX XXXXX XXXXX
XXXXX XXXXX XXXXX XXXXX
F
button.
XXXXXXXXX
XXXXXXXXX
XXXXXXXXX
XXXXXXXXXXXXX
XXXXX
XXXXX
XXXXX
**On the rating plate the
serial number is 12 digits
7