Assembly - EINHELL NEW GENERATION NTS 1200 Originalbetriebsanleitung

Anleitung_NTS 1200_SPK7:_
GB

7. Assembly

Important. Always pull out the power plug before
carrying out any maintenance or conversion
work on the bench type circular saw.
7.1 Fitting the saw blade (Fig. 2/3)
Important! Pull out the power plug.
Loosen the chip bin cover (19) by undoing the
fixing screws (20) and swing it up.
Undo the nut with a ring wrench (30) on the nut
itself and a second wrench (31) on the motor
shaft (32) to apply counter-pressure.
Important! Turn the nut in the direction of
rotation of the saw blade (4).
Take off the outer flange and pull the old saw
blade (4) off the inner flange by dropping the
blade at an angle.
Clean the mounting flange.
Fit the new saw blade in reverse order.
Important! Note the direction of rotation (see
arrow on the saw blade).
7.2 Adjusting the splitter (Fig. 4/5/6)
Remove the saw blade guard (2) (see 7.3).
Take out the table insert (6) (see 7.4).
Slacken the two hexagon socket-head screws
(24).
Adjust the splitter (5) so that the gap between the
saw blade (4) and the splitter (5) equals 3 - 5 mm
(see Fig. 6)
The splitter (5) has to be in line with the saw
blade (4) in longitudinal direction.
Retighten the two screws (24).
The setting of the splitter has to be checked each
time after changing the saw blade.
7.3 Fitting the saw blade guard (Fig. 4)
Mount the saw blade guard (2) on the splitter (5)
and align.
Insert the screw through the hole in the saw
blade guard (2) and in the splitter (5) and secure
it with the wing nut.
To remove the saw blade guard, proceed in
reverse order.
7.4 Replacing the table insert (Fig. 4)
Important: Remove the power plug!
Remove the 6 screws (23).
Take off the saw blade guard (2) (see 7.3).
Lift the worn table insert (6) up and out.
Fit the replacement table insert by following the
above in reverse.
16
15.12.2010 12:58 Uhr Seite 16
7.5 Connecting the dust extraction device
Connect a suitable dust extraction device to the
two extractor sockets (33) and (34). If required,
use a matching adapter.
8.0 Using the saw
Unwind the power cable from its holder and connect
the power plug to a suitable socket.
8.1 On/Off switch (Fig. 1)
The saw can be switched on by pressing the
green pushbutton.
The red pushbutton has to be pressed to switch
off the saw.
8.1.1 Cutting depth (Fig. 11)
Turn the round handle (17) to set the blade (4) to
the required cutting depth.
Turn anti-clockwise:
Turn clockwise:
8.2 Parallel stop
8.2.1 Stop height (Fig. 7/8)
The stop rail (25) supplied has two different
guide faces (high and low).
For thick material you must use the stop rail (25)
as shown in Fig. 7, for thin material you must use
the stop rail as shown in Fig. 8.
To change the height of the stop, slacken the two
knurled screws and pull the stop rail off the
carrier rail.
Turn the stop rail (25) 90° to the left or the right,
depending on the required height of the stop,
and plug in back on the carrier rail.
Re-tighten the knurled screws.
8.2.2. Stop length (Fig. 7/8)
To prevent the workpiece becoming jammed,
always slide the stop rail (25) to the front edge of
the table (1) and fix it in place with the two
knurled screws (see 8.2.1).
8.2.3 Cutting width (Fig. 8)
The parallel stop (7) has to be used when
making longitudinal cuts in wooden workpieces.
Slide the parallel stop (7) to the right or left side
of the saw table (1).
The parallel stop (7) can be set to the required
dimension with the help of the scale (b) engraved
on the saw table (1).
Tighten the two star grip screws (12) in order to
fix the parallel stop (7).
larger cutting depth
smaller cutting depth