Before Starting The Equipment; Assembly - EINHELL TE-CC 2025 UF Originalbetriebsanleitung

Operation
L sound pressure level ..................... 96,4 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ..................... 109,4 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
The quoted values are emission values and not
necessarily reliable workplace values. Although
there is a correlation between emission and im-
mission levels it is impossible to draw any certain
conclusions as to the need for additional precau-
tions. Factors with a potential infl uence on the ac-
tual immission level at the workplace include the
duration of impact, the type of room, and other
sources of noise etc., e.g. the number of machi-
nes and other neighboring operations. Reliable
workplace values may also vary from country to
country. With this information the user should at
least be able to make a better assessment of the
dangers and risks involved.
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
Anl_TE_CC_2025_UF_SPK9.indb 26 Anl_TE_CC_2025_UF_SPK9.indb 26
GB

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
•
Unpack the bench-type circular saw and
check it for damage which may have occurred
in transit.
•
The machine has to be set up where it can
stand firmly, e.g. on a work bench, or it must
be bolted to a strong base.
•
All covers and safety devices have to be pro-
perly fitted before the machine is switched on.
•
It must be possible for the saw blade to run
freely.
•
When working with wood that has been pro-
cessed before, watch out for foreign bodies
such as nails or screws etc.
•
Before you actuate the On/Off switch, make
sure that the saw blade is correctly fitted and
that the machine's moving parts run smoothly.

6. Assembly

Danger! Pull out the power plug before carry-
ing out any maintenance, resetting or assem-
bly work on the cutting-off machine!
6.1 Fitting the table length extension
(Fig. 2a, 2b)
•
Turn the bench-type circular saw around and
place it on the floor or on a suitable surface
so that the saw table faces down.
•
Insert the table width extension (33) and the
table length extension (39) in the saw table.
The table width extension must be pushed in
fully before it is secured.
•
Secure the table length extension and the
table width extension with the screws (a)
against being pulled out fully. Fit the locking
screws (b).
6.2 Fitting the base frame (Fig. 1, 3-5)
•
Open the lock on the base frame by pressing
the lever (35) inwards.
•
Let the legs of the base frame latch into posi-
tion again in the swung-out position.
•
Use the axle screws (f), washers (g), spacer
sleeve (h) and nuts (i) to fasten the wheels
- 26 -
10.03.2017 07:33:34 10.03.2017 07:33:34