Before Starting The Equipment; Assembly - EINHELL TC-TS 1200 Originalbetriebsanleitung

dangers and risks involved.
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
•
Unpack the bench-type circular saw and
check it for damage which may have occurred
in transit.
•
The machine has to be set up where it can
stand firmly, e.g. on a work bench, or it must
be bolted to a strong base.
•
All covers and safety devices have to be pro-
perly fitted before the machine is switched on.
•
It must be possible for the saw blade to run
freely.
•
When working with wood that has been pro-
cessed before, watch out for foreign bodies
such as nails or screws etc.
•
Before you actuate the On/Off switch, make
sure that the saw blade is correctly fitted and
that the machine's moving parts run smoothly.
Anl_TC_TS_1200_SPK1.indb 24 Anl_TC_TS_1200_SPK1.indb 24
GB

6. Assembly

Danger! Pull out the power plug before carry-
ing out any maintenance, resetting or assem-
bly work on the cutting-off machine!
6.1 Fitting / removing the saw blade guard
(Fig. 3)
•
Mount the saw blade guard (2) on the splitter
(5) so that the screw fits through the hole (18)
in the splitter.
•
Do not tighten the screw (15) too far – the bla-
de guard must be able to move freely.
•
To remove the saw blade guard, proceed in
reverse order.
Warning!
The guard hood (2) must always be lowered
over the workpiece before you begin to cut.
6.2 Changing the table insert (Figure 4)
•
To prevent increased likelihood of injury the
table insert should be changed whenever it is
worn or damaged.
•
Remove the saw blade guard (2).
•
Remove the screws (33)
•
Take out the worn table insert (6).
•
To fit the replacement table insert, proceed in
reverse order.
6.3 Adjusting the splitter (Fig. 5-9)
•
Danger! Pull out the power plug.
•
Set the blade (4) to the lowest cutting depth,
move to the 0° position and lock in place.
•
Remove the cover plate (see 6.4)
•
Slacken the fixing screw (19).
•
The distance between the blade (4) and the
splitter (5) should be 3-5mm.
•
Retighten the screw (19) and refit the cover
plate (32).
6.4 Fitting/replacing the blade (Fig. 5.6)
•
Danger! Pull out the power plug!
•
Undo the screws (17) on the cover plate (32)
on the underside of the saw.
•
Undo the screws (c) on the lower saw blade
guard (28) and swing it up.
•
Caution! Turn the nut in the direction of rotati-
on of the saw blade.
•
Take off the outer flange and pull the old saw
blade off the inner flange by dropping the bla-
de at an angle.
•
Clean the blade flange thoroughly before fit-
ting the new blade.
- 24 -
03.11.2016 08:51:18 03.11.2016 08:51:18