Using The Remote Control Unit; Setting Up The System; Remote Control Unit (Rc-896) - Denon AVR-1602 Bedienungsanleitung

ENGLISH

9 USING THE REMOTE CONTROL UNIT

Following the procedure outlined below, insert the batteries before using the remote control unit.
Range of operation of the remote control unit
B
30°
30°
Approx. 7 m
Inserting the batteries
q Press as shown by the arrow w Insert the R6P/AA batteries properly,
and slide off.
NOTES:
• Use only R6P/AA batteries for replacement.
• Be sure the polarities are correct. (See the illustration inside the battery compartment.)
• Remove the batteries if the remote control transmitter will not be used for an extended period of time.
• If batteries leak, dispose of them immediately. Avoid touching the leaked material or letting it come in contact
with clothing, etc. Clean the battery compartment thoroughly before installing new batteries.
• Have replacement batteries on hand so that the old batteries can be replaced as quickly as possible when the
time comes.
• Even if less than a year has passed, replace the batteries with new ones if the set does not operate even when
the remote control unit is operated nearby the set. (The included battery is only for verifying operation.
Replace it with a new battery as soon as possible.)
8
Downloaded from www.Manualslib.com
Point the remote control unit at the remote control
sensor as shown on the diagram at the left.
NOTES:
• The remote control unit can be used from a straight
distance of approximately 7 meters, but this distance
will shorten or operation will become difficult if there
are obstacles between the remote control unit and
the remote control sensor, if the remote control
sensor is exposed to direct sunlight or other strong
light, or if operated from an angle.
• Neon signs or other devices emitting pulse-type noise
nearby may result in malfunction, so keep the set as
far away from such devices as possible.
e Close the lid.
as shown on the diagram.
manuals search engine

10 SETTING UP THE SYSTEM

• Once all connections with other AV components have been completed as described in "CONNECTIONS" (see
pages 5 to 7), make the various settings described below on the display.
These settings are required to set up the listening room's AV system centered around the this unit.
1
Set the slide switch to "AUDIO".
CD MD/CDR
AUDIO VIDEO
2
Use the following buttons to set up the system:
VIDEO SELECT CD·MD/CDR·DVD/VDP DISC SKIP+
TITLE
8 3 9
2
6 7
SYSTEM SURROUND
SET UP MENU
MASTER
CH SELECT VOL
SELECT
T.TONE STATUS MUTING
RETURN DISPLAY
• System setup items and default values (set upon shipment from the factory)
System setup
Input the combination of speakers in your system and
their corresponding sizes (SMALL for regular speakers,
Speaker
LARGE for full-size, full-range) to automatically set the
Configuration
composition of the signals output from the speakers and
the frequency response.
Subwoofer This selects the subwoofer speaker for playing deep bass
Mode signals.
This parameter is for optimizing the timing with which
Delay Time the audio signals are produced from the speakers and
subwoofer according to the listening position.
This adjusts the volume of the signals output from the
Channel
speakers and subwoofer for the different channels in
Level
order to obtain optimum effects.
Digital
Inputs
This assigns the digital input jacks for the
Digital Input
different input sources.
source
NOTE:
• The system setup is not displayed when "HEADPHONE ONLY" is selected.
SYSTEM SETUP button
Press this to display the system setup on the display.
CURSOR buttons (•, ª, 0, 1)
Press this change what appears on the display.
SELECT button
Press this to switch the display.
Also use this button to complete the setting.
Default settings
Center
Front Sp. Surround Sp.
Sp.
Large Small Small
Subwoofer mode = Normal
Front & Subwoofer Center Surround L & R
3.6 m 3.6 m 3.0 m
Front Surround Surround
Front
Subwoofer Center
L R L
0 dB 0 dB 0 dB 0 dB 0 dB
COAXIAL OPTICAL
Input
DVD/VDP TV/DBS
Subwoofer
Yes
—
—
—
R
0 dB —